Graco Inc 3A0149C important safety instructions Fire and Explosion Hazard

Page 4

Warnings

Warnings

The following are general warnings related to the setup, use, grounding, maintenance, and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols that appear in the body of the manual refer to these general warnings. When these symbols appear throughout the man- ual, refer back to these pages for a description of the specific hazard.

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).

• Keep work area free of debris, including solvent, rags and gasoline.

Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present.

Ground all equipment in the work area. See Grounding instructions.

Use only grounded hoses.

Hold gun firmly to side of grounded pail when triggering into pail.

If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.

Keep a working fire extinguisher in the work area.

SKIN INJECTION HAZARD

High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

• Do not spray without tip guard and trigger guard installed.

Engage trigger lock when not spraying.

Do not point gun at anyone or at any part of the body.

Do not put your hand over the spray tip.

Do not stop or deflect leaks with your hand, body, glove, or rag.

Follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing equipment.

Tighten all fluid connections before operating the equipment.

Check hoses and couplings daily. Replace worn or damaged parts immediately.

4

3A0149C

Image 4
Contents Model G15 Model G40 Model G40 w/RAC tipContents ModelsRelated Manuals Fire and Explosion Hazard Equipment Misuse Hazard Typical Installation Ventilate the Spray Booth InstallationGrounding Air Line Fluid LineSetup Reverse-A-CleanRAC Tip Assembly Pressure Relief Procedure OperationTrigger Lock EngageddisengagedHow the Air-Assisted Spray Gun Operates Spray Pattern AdjustmentClose Open Incorrect Hvlp Operation Fluid ApplicationCorrect Daily Gun Care, Flushing, and Cleaning Fluid Filter Maintenance General System MaintenanceFlushing and Cleaning TI6729A Reverse-A-CleanRAC Tip EngagedDisengaged TI6580A DisengagedTroubleshooting Problem Cause SolutionTroubleshooting Fan Valve Replacement RepairRepair Kits Complete Gun Packing RepairNeedle Repair 5g* 5c13‡ 14‡ Fluid Tube Replacement Air Valve RepairRepair 3A0149C Reassembly 5b carbide only Parts Part No. Description Qty Washer PtfeDescription AIR CAPParts 3A0149C Part No C857, G40 Gun with RAC Tip Ref. No. Part No. Description Qty TIP GUARD/AIR CAP AssySpray Tip Selection Chart Spray Tips, for use with G15/G40 Air CapAAM Fine Finish Spray Tips GG4 Industrial Spray TipsAAF Fine Finish Pre-Orifice Spray Tips RAC SwitchTips, for use with G40 RAC Air CapLTX RAC Spray Tips FFT Fine Finish RAC Spray Tips WRX WideRAC Spray TipsAccessories Ultimate Gun Cleaning Kit 15C161 Fan Valve Fine Adjustment KitPlastic Seat Repair Kit SST Seat Repair KitPart Interchangeability Guide Dimensions Model G40Category Data Technical Data10.6 Gun Inlet Pressure PSI Graco Standard Warranty Graco Information