Graco Inc GX-7A Model Final Assembly, No. Part No. Description, Module see GX-7A Mix Mod

Page 31

Parts

GX-7A Model Final Assembly

Part Numbers 295542, 295543, 295544, 295545

Ref.
No. Part No. Description			Qty.
1	295810	Spray gun handle	1
2	15B772	Air hose	1
3	295596	Coupler plug	1
4	295597	Coupler	1
5	296834	R-gun block screen screw	1
		assembly (includes 6, 7, 8, 9)
6		R-gun block screen screw	1
7	296693	Screen screw seal (pack of 2)	-
	296723	Screen screw seal (pack of 10)	-
8	296792	Screen, 80 mesh (pack of 10)	-
	296724	Screen, 80 mesh (pack of 50)	-
9	296722	Check valve assembly	-
		(pack of 10)
10	295384	Gun block	1
11		Module; see GX-7A Mix Mod-	1
		ule Kit, page 43
12	296976	PCD body	1
13		Tip; see Tip Kits, page 48	1
14	296978	Front packing (pack of 5)	1
15	295868	O-ring	1
16	296832	PCD retainer	1
17	296831	Air cap	1
18	296128	Coupling block gasket (pkg 2)	1
19	295433	Coupling block mounting screw	1
	296979	Coupling block mounting screw	-
		kit (pack of 2)
20	296833	A-gun block screen screw	1
		assembly (includes 6, 8, 9, 21)
21		A-gun block screen screw	1
22	296828	Rear packing retainer	1
23	296829	Rear seal packing	-
		(pack of 5)
24	296830	Rear seal retainer	1
25	296692	Valving rod	1
26	100030	Fitting	1

311321H

31

Image 31

Contents 311321H Important Safety InstructionsGX-7 Models ContentsPersonal Protective Equipment Fire and Explosion Hazard Pressurized Aluminum Parts Hazard Model GX-7A Overall ViewModel GX-7 DI Trigger Model GX-7Locknut Valving Rod Rear Stop Gun Block Air Cap ValveGX-7A Centerline Components Centerline ComponentsGX-7 400 Centerline Components GX-7A Mixing Module Mixing ModuleKeep a and B Components Separate Safety PositionOperation Basics Isocyanate HazardDisconnect Air Hoses Disengage Safety StopAir Hose Connection Connect Air HosesCoupling Block Installation and RemovalManual Valves Optional Configuration Air Inlet ConfigurationRemove Coupling Block Do not Overtighten Mixing Module and PCD InstallationGX-7A and GX-7 400 Models Only Valving Rod AdjustmentGX-7 DI Model Only Initial Set Up Daily Shutdown Daily Start-upTrigger Gun Pressure Relief ProcedureGun Service Kits MaintenanceClean Spray Gun Procedure Flush Gun Repair Service Screen ScrewRemove Centerline Components Remove valving rod. Rod Draw Bar Valving Rod Install Centerline Components GX-7 DI Shown Replace End Cap and Air Piston AssemblyReplace Trigger Valve O-Ring Replace Trigger Valve O-RingsUnthread Cap from PCD Body Clean Mixing ModuleInstall Mixing Module Install Mixing ModuleGX-7A Model Shown Clean Pattern Control DiscParts GX-7A Model Final AssemblyNo. Part No. Description GX-7A Model Final AssemblyModule see GX-7A Mix Mod GX-7 DI Model Final Assembly Module see GX-7 DI Model Specifications , GX-7 DI Model Final AssemblyNo. Part No. Description Qty GX-7 400 Model Final Assembly Module Kit , GX-7 400 Model Final AssemblyGX-7A Model Handle Assembly Description GX-7 Model Handle AssemblyGX-7 DI Model Handle Assembly Description Qty GX-7 DI Model Handle AssemblyGX-7 400 Model Handle Assembly GX-7 400 Model Handle Assembly All models Coupling Block AssemblyGX-7A Mix Module Kit SpecificationsTip Set-Up Chart for GX-7A ModelModule Only Size Ref Module Kits Cleanout Drill Iso PortGX-7 400 Mix Module Kit Quantity In/mmTip Kits for GX-7 400 Gun No. Ref Quantity Set-up Chart for GX-7 400 ModelRound Spray Pattern GX-7 DI Model SpecificationsModule/Tip Data for Chemical Sprayed at 2500 PSI Output Pattern Lbs/minRound Tip Kits Size Quantity Tip KitsTool Kits For GX-7A and GX-7 DI ModelsCategory Data Technical DataGraco Standard Warranty