Graco Inc GX-7 400, 311321H, GX-7A GX-7 DI Model Final Assembly, No. Part No. Description Qty

Page 33

Parts

GX-7 DI Model Final Assembly (295541)

Ref.
No. Part No. Description			Qty.
1	295809	Spray gun handle assembly	1
2	15B772	Air hose, 1/4 in. x 23 in. (FXF)	1
3	295596	Coupler plug	1
4	295597	Coupler	1
5	295835	R-screen screw	1
6	296792	Screen, 80 mesh (pack of 10)	-
	296724	Screen, 80 mesh (pack of 50)	-
7	296713	Check valve assembly	2
		(pack of 2)
8	295860	Gun block	1
9		Module; see GX-7 DI Model	1
		Specifications, page 47
10	295837	Module retainer	1
11		Tip; see Tip Kits, page 48	1
12	296865	Tip retainer	1
13	295838	Air cap	1
14	296128	Coupling block gasket	-
		(pack of 2)
15	295433	Coupling block mounting screw	1
	296979	Coupling block mounting screw	-
		(pack of 2)
16	295834	A-screen screw	1
17	295836	Rear seal gland	1
18	296864	Rear seal retainer assembly	1
19	296829	Rear seal packing (pack of 5)	-
20	295383	Coupling block (not shown)	1
21	100030	Fitting	1

311321H

33

Image 33

Contents Important Safety Instructions 311321HGX-7 Models ContentsPersonal Protective Equipment Fire and Explosion Hazard Pressurized Aluminum Parts Hazard Overall View Model GX-7AModel GX-7 DI Locknut Model GX-7Valving Rod Rear Stop Gun Block Air Cap Valve TriggerGX-7A Centerline Components Centerline ComponentsGX-7 400 Centerline Components GX-7A Mixing Module Mixing ModuleOperation Basics Safety PositionIsocyanate Hazard Keep a and B Components SeparateAir Hose Connection Disengage Safety StopConnect Air Hoses Disconnect Air HosesInstallation and Removal Coupling BlockManual Valves Air Inlet Configuration Optional ConfigurationRemove Coupling Block Do not Overtighten Mixing Module and PCD InstallationValving Rod Adjustment GX-7A and GX-7 400 Models OnlyGX-7 DI Model Only Initial Set Up Daily Shutdown Daily Start-upTrigger Gun Pressure Relief ProcedureMaintenance Gun Service KitsClean Spray Gun Procedure Flush Gun Service Screen Screw RepairRemove Centerline Components Remove valving rod. Rod Draw Bar Valving Rod Install Centerline Components GX-7 DI Shown Replace End Cap and Air Piston AssemblyReplace Trigger Valve O-Ring Replace Trigger Valve O-RingsUnthread Cap from PCD Body Clean Mixing ModuleInstall Mixing Module Install Mixing ModuleGX-7A Model Shown Clean Pattern Control DiscParts GX-7A Model Final AssemblyGX-7A Model Final Assembly No. Part No. DescriptionModule see GX-7A Mix Mod GX-7 DI Model Final Assembly GX-7 DI Model Final Assembly Module see GX-7 DI Model Specifications ,No. Part No. Description Qty GX-7 400 Model Final Assembly Module Kit , GX-7 400 Model Final AssemblyGX-7A Model Handle Assembly Description GX-7 Model Handle AssemblyGX-7 DI Model Handle Assembly Description Qty GX-7 DI Model Handle AssemblyGX-7 400 Model Handle Assembly GX-7 400 Model Handle Assembly All models Coupling Block AssemblyGX-7A Mix Module Kit SpecificationsTip Set-Up Chart for GX-7A ModelGX-7 400 Mix Module Kit Module Kits Cleanout Drill Iso PortQuantity In/mm Module Only Size RefTip Kits for GX-7 400 Gun No. Ref Quantity Set-up Chart for GX-7 400 ModelModule/Tip Data for Chemical Sprayed at 2500 PSI Output GX-7 DI Model SpecificationsPattern Lbs/min Round Spray PatternTool Kits Tip KitsFor GX-7A and GX-7 DI Models Round Tip Kits Size QuantityCategory Data Technical DataGraco Standard Warranty