Graco Inc 311321H, GX-7 400, GX-7 DI important safety instructions Set-Up Chart for GX-7A Model, Tip

Page 44

Specifications

Set-Up Chart for GX-7A Model

Pres-		Pattern			Polyol
sure	Output	Dia.	Module Part		Port	No.	Iso Port	No.
(psi)	(lbs/min)	(inches)	No.		Size	Orifices	Size	Orifices	Tip


			Round Spray Pattern


1000	22	❄22	296909 (#1)		.0320	4	.0320	4	296712

1000	12	❄12	296919 (#3)		.0180	4	.0225	4	296710

1600	16	❄14	296923 (#5)		.0280	4	.0225	4	296710

2000	30	❄24	296909 (#1)		.0320	4	.0320	4	296694

3000	40	❄24	296921 (#4)		.0320	4	.0350	4	296695


				Pour Pattern


600	3.5	N/A	296875 (A2)		.0180	1	.0180	1	296697

600	12	N/A	296876 (A3)		.0390	1	.0390	1	296697


			Fan Spray Pattern


1000	12	❖ 16 x 4	296925 (#7)		.0280	2	.0280	2	296704

1500	24	❖ 22 x 4	296906		.0360	2	.0360	2	296703
			(#10)

1500	5	❖ 16 x 3	296910		.0210	2	.0210	2	296705
			(#12)

❄At 24 in. above substrate

❖ At 18 in. above substrate

44

311321H

Image 44

Contents GX-7 Important Safety Instructions311321H Contents ModelsPersonal Protective Equipment Fire and Explosion Hazard Pressurized Aluminum Parts Hazard Model GX-7 DI Overall ViewModel GX-7A Model GX-7 LocknutValving Rod Rear Stop Gun Block Air Cap Valve TriggerCenterline Components GX-7A Centerline ComponentsGX-7 400 Centerline Components Mixing Module GX-7A Mixing ModuleSafety Position Operation BasicsIsocyanate Hazard Keep a and B Components SeparateDisengage Safety Stop Air Hose ConnectionConnect Air Hoses Disconnect Air HosesManual Valves Installation and RemovalCoupling Block Remove Coupling Block Air Inlet ConfigurationOptional Configuration Mixing Module and PCD Installation Do not OvertightenGX-7 DI Model Only Valving Rod AdjustmentGX-7A and GX-7 400 Models Only Initial Set Up Daily Start-up Daily ShutdownPressure Relief Procedure Trigger GunClean Spray Gun Procedure MaintenanceGun Service Kits Flush Gun Remove Centerline Components Service Screen ScrewRepair Remove valving rod. Rod Draw Bar Valving Rod Install Centerline Components Replace End Cap and Air Piston Assembly GX-7 DI ShownReplace Trigger Valve O-Rings Replace Trigger Valve O-RingClean Mixing Module Unthread Cap from PCD BodyInstall Mixing Module Install Mixing ModuleClean Pattern Control Disc GX-7A Model ShownGX-7A Model Final Assembly PartsModule see GX-7A Mix Mod GX-7A Model Final AssemblyNo. Part No. Description GX-7 DI Model Final Assembly No. Part No. Description Qty GX-7 DI Model Final AssemblyModule see GX-7 DI Model Specifications , GX-7 400 Model Final Assembly GX-7 400 Model Final Assembly Module Kit ,GX-7A Model Handle Assembly GX-7 Model Handle Assembly DescriptionGX-7 DI Model Handle Assembly GX-7 DI Model Handle Assembly Description QtyGX-7 400 Model Handle Assembly GX-7 400 Model Handle Assembly Coupling Block Assembly All modelsSpecifications GX-7A Mix Module KitSet-Up Chart for GX-7A Model TipModule Kits Cleanout Drill Iso Port GX-7 400 Mix Module KitQuantity In/mm Module Only Size RefSet-up Chart for GX-7 400 Model Tip Kits for GX-7 400 Gun No. Ref QuantityGX-7 DI Model Specifications Module/Tip Data for Chemical Sprayed at 2500 PSI OutputPattern Lbs/min Round Spray PatternTip Kits Tool KitsFor GX-7A and GX-7 DI Models Round Tip Kits Size QuantityTechnical Data Category DataGraco Standard Warranty