Graco Inc 311321H, GX-7 DI, GX-7A important safety instructions GX-7 400 Model Handle Assembly

Page 41

Parts

GX-7 400 Model Handle Assembly (295799)

Ref.
No.	Part No.	Description	Qty.
1	106245	Cap screw, SCH	2
2	295662	Pipe plug	1
3†❄	106555	Packing o-ring	6
4†❄	103337	Packing o-ring	3
5	295684	Socket head cap screw	4
6	295438	Stop nut, elastic, 5-40	1
7†❄	295685	O-ring	2
8†	295405	Needle valve, packing	1
9	295692	Spray gun trigger	1
10	295693	Pipe plug	1
11	C20003	Socket head cap screw	1
12❄	295442	Spring	1
13	295695	Button head cap screw	1
14	295676	Spring	1
15	295771	Two-position stop	1
16†	295681	O-ring	1
17	295682	Draw rod bar	1
18†	295683	O-ring	1
19	295663	Front cylinder stop	1
20†	514279	O-ring	1
21	295664	Air piston	1
22	295665	Pipe nipple fitting	1
23	295666	Stop clamp screw	1
24†	295667	Pellet	1
25	295668	Spring	1
26	295669	Socket head cap screw,	1
		modified
27	295671	Trigger mounting screw	1
28	295673	Gun block base	1
29†	295674	Gasket	1
30	295675	Air cylinder	1
31	295677	Air needle valve	1
32	295678	Cylinder end cap	1
33	295690	Cylinder clamp	1
34	295686	Valve liner	1
35	295687	Valve spool	1
36	295688	Retainer valve nut	1
37	295689	Spring seat	1
38	296862	Gun handle	1
39†	295706	O-ring	1
40	295708	Spacer	1

†Parts included in Air Cylinder Rebuild Kit 296895 (purchase separately).

❄Parts included in Trigger Valve Rebuild Kit 296897(purchase separately).

311321H

41

Image 41

Contents GX-7 Important Safety Instructions311321H Models ContentsPersonal Protective Equipment Fire and Explosion Hazard Pressurized Aluminum Parts Hazard Model GX-7 DI Overall ViewModel GX-7A Locknut Model GX-7Valving Rod Rear Stop Gun Block Air Cap Valve TriggerGX-7A Centerline Components Centerline ComponentsGX-7 400 Centerline Components GX-7A Mixing Module Mixing ModuleOperation Basics Safety PositionIsocyanate Hazard Keep a and B Components SeparateAir Hose Connection Disengage Safety StopConnect Air Hoses Disconnect Air HosesManual Valves Installation and RemovalCoupling Block Remove Coupling Block Air Inlet ConfigurationOptional Configuration Do not Overtighten Mixing Module and PCD InstallationGX-7 DI Model Only Valving Rod AdjustmentGX-7A and GX-7 400 Models Only Initial Set Up Daily Shutdown Daily Start-upTrigger Gun Pressure Relief ProcedureClean Spray Gun Procedure MaintenanceGun Service Kits Flush Gun Remove Centerline Components Service Screen ScrewRepair Remove valving rod. Rod Draw Bar Valving Rod Install Centerline Components GX-7 DI Shown Replace End Cap and Air Piston AssemblyReplace Trigger Valve O-Ring Replace Trigger Valve O-RingsUnthread Cap from PCD Body Clean Mixing ModuleInstall Mixing Module Install Mixing ModuleGX-7A Model Shown Clean Pattern Control DiscParts GX-7A Model Final AssemblyModule see GX-7A Mix Mod GX-7A Model Final AssemblyNo. Part No. Description GX-7 DI Model Final Assembly No. Part No. Description Qty GX-7 DI Model Final AssemblyModule see GX-7 DI Model Specifications , GX-7 400 Model Final Assembly Module Kit , GX-7 400 Model Final AssemblyGX-7A Model Handle Assembly Description GX-7 Model Handle AssemblyGX-7 DI Model Handle Assembly Description Qty GX-7 DI Model Handle AssemblyGX-7 400 Model Handle Assembly GX-7 400 Model Handle Assembly All models Coupling Block AssemblyGX-7A Mix Module Kit SpecificationsTip Set-Up Chart for GX-7A ModelGX-7 400 Mix Module Kit Module Kits Cleanout Drill Iso PortQuantity In/mm Module Only Size RefTip Kits for GX-7 400 Gun No. Ref Quantity Set-up Chart for GX-7 400 ModelModule/Tip Data for Chemical Sprayed at 2500 PSI Output GX-7 DI Model SpecificationsPattern Lbs/min Round Spray PatternTool Kits Tip KitsFor GX-7A and GX-7 DI Models Round Tip Kits Size QuantityCategory Data Technical DataGraco Standard Warranty