Graco Inc GX-7 DI Set-up Chart for GX-7 400 Model, Tip Kits for GX-7 400 Gun No. Ref Quantity

Page 46

Specifications

Set-up Chart for GX-7 400 Model

Pres-		Pattern		Polyol
sure	Output	Dia.	Module Part	Port	No.	Iso Port	No.
(psi)	(lbs/min)	(inches)	No.	Size	Orifices	Size	Orifices	Tip


			Round Spray Pattern


1500	3.5	✖ 8	296885 (402)	.0180	1	.0180	1	296858


			Fan Spray Pattern


1500	3.5	❖ 16 x 3	296859 (451)	.0180	1	.0180	1	296853

1500	4.5	❖ 16 x 3	296888 (452)	.0200	1	.0200	1	296853

1500	8.0	❖ 16 x 3	296891 (453)	.0225	2	.0250	2	296855

✖At 24 in. above substrate

❖ At 18 in. above substrate

Tip Kits (for GX-7 400 Gun)

Part No.	No. Ref.	Quantity


296858	40 Round	1

296852	210 Fan	1

296853	212 Fan	1

296854	212 Fan	5

296855	213 Fan	1

296856	213 Fan	5

296857	214 Fan	1

296892	TOM	1

46

311321H

Image 46

Contents 311321H Important Safety InstructionsGX-7 Contents ModelsPersonal Protective Equipment Fire and Explosion Hazard Pressurized Aluminum Parts Hazard Model GX-7A Overall ViewModel GX-7 DI Valving Rod Rear Stop Gun Block Air Cap Valve Model GX-7Locknut TriggerCenterline Components GX-7A Centerline ComponentsGX-7 400 Centerline Components Mixing Module GX-7A Mixing ModuleIsocyanate Hazard Safety PositionOperation Basics Keep a and B Components SeparateConnect Air Hoses Disengage Safety StopAir Hose Connection Disconnect Air HosesCoupling Block Installation and RemovalManual Valves Optional Configuration Air Inlet ConfigurationRemove Coupling Block Mixing Module and PCD Installation Do not OvertightenGX-7A and GX-7 400 Models Only Valving Rod AdjustmentGX-7 DI Model Only Initial Set Up Daily Start-up Daily ShutdownPressure Relief Procedure Trigger GunGun Service Kits MaintenanceClean Spray Gun Procedure Flush Gun Repair Service Screen ScrewRemove Centerline Components Remove valving rod. Rod Draw Bar Valving Rod Install Centerline Components Replace End Cap and Air Piston Assembly GX-7 DI ShownReplace Trigger Valve O-Rings Replace Trigger Valve O-RingClean Mixing Module Unthread Cap from PCD BodyInstall Mixing Module Install Mixing ModuleClean Pattern Control Disc GX-7A Model ShownGX-7A Model Final Assembly PartsNo. Part No. Description GX-7A Model Final AssemblyModule see GX-7A Mix Mod GX-7 DI Model Final Assembly Module see GX-7 DI Model Specifications , GX-7 DI Model Final AssemblyNo. Part No. Description Qty GX-7 400 Model Final Assembly GX-7 400 Model Final Assembly Module Kit ,GX-7A Model Handle Assembly GX-7 Model Handle Assembly DescriptionGX-7 DI Model Handle Assembly GX-7 DI Model Handle Assembly Description QtyGX-7 400 Model Handle Assembly GX-7 400 Model Handle Assembly Coupling Block Assembly All modelsSpecifications GX-7A Mix Module KitSet-Up Chart for GX-7A Model TipQuantity In/mm Module Kits Cleanout Drill Iso PortGX-7 400 Mix Module Kit Module Only Size RefSet-up Chart for GX-7 400 Model Tip Kits for GX-7 400 Gun No. Ref QuantityPattern Lbs/min GX-7 DI Model SpecificationsModule/Tip Data for Chemical Sprayed at 2500 PSI Output Round Spray PatternFor GX-7A and GX-7 DI Models Tip KitsTool Kits Round Tip Kits Size QuantityTechnical Data Category DataGraco Standard Warranty