Graco Inc GX-7A, 311321H GX-7 DI Model Specifications, Pattern Lbs/min, Round Spray Pattern

Page 47

Specifications

GX-7 DI Model Specifications

Module/Tip Data for Chemical Sprayed at 2500 PSI

				❄Output
✖ Module Kit	Cleanout Drill	Ref. No.	❄Pattern	(lbs/min)

		Fan Spray Pattern


296900 (#2)	246625	212	12 in. wide	12

	(.086 diameter)	206	20 in. wide	22
		213	12 in. wide	12

		204	20 in. wide	21

296901 (#4)	248892	212	10 in. wide	8

	(.028 diameter)	206	24 in. wide	11
		204	18 in. wide	10

296903 (#5)	246816	212	11 in. wide	4

	(.018 diameter)	213	12 in. wide	4
		208	8 in. wide	4

Round Spray Pattern

296903 (#5)

246816

(.018 diameter)

40	4 in. diameter	8
55	7 in. diameter	9.5

70	8 in. diameter	9.75

90	10 in. diameter	9.75

❄Actual results may vary due to chemical system characteristics, temperature, pressure, and ratio.

✖Includes appropriate cleanout drills.

Mix Module Kit

Part No.	Size Ref.	Quantity

296898	PEEK 018/018	1

296899	PEEK 028/028	1

Module Only

Part No.	Size Ref.

296902	#5

311321H

47

Image 47

Contents GX-7 Important Safety Instructions311321H Models ContentsPersonal Protective Equipment Fire and Explosion Hazard Pressurized Aluminum Parts Hazard Model GX-7 DI Overall ViewModel GX-7A Trigger Model GX-7Locknut Valving Rod Rear Stop Gun Block Air Cap ValveGX-7A Centerline Components Centerline ComponentsGX-7 400 Centerline Components GX-7A Mixing Module Mixing ModuleKeep a and B Components Separate Safety PositionOperation Basics Isocyanate HazardDisconnect Air Hoses Disengage Safety StopAir Hose Connection Connect Air HosesManual Valves Installation and RemovalCoupling Block Remove Coupling Block Air Inlet ConfigurationOptional Configuration Do not Overtighten Mixing Module and PCD InstallationGX-7 DI Model Only Valving Rod AdjustmentGX-7A and GX-7 400 Models Only Initial Set Up Daily Shutdown Daily Start-upTrigger Gun Pressure Relief ProcedureClean Spray Gun Procedure MaintenanceGun Service Kits Flush Gun Remove Centerline Components Service Screen ScrewRepair Remove valving rod. Rod Draw Bar Valving Rod Install Centerline Components GX-7 DI Shown Replace End Cap and Air Piston AssemblyReplace Trigger Valve O-Ring Replace Trigger Valve O-RingsUnthread Cap from PCD Body Clean Mixing ModuleInstall Mixing Module Install Mixing ModuleGX-7A Model Shown Clean Pattern Control DiscParts GX-7A Model Final AssemblyModule see GX-7A Mix Mod GX-7A Model Final AssemblyNo. Part No. Description GX-7 DI Model Final Assembly No. Part No. Description Qty GX-7 DI Model Final AssemblyModule see GX-7 DI Model Specifications , GX-7 400 Model Final Assembly Module Kit , GX-7 400 Model Final AssemblyGX-7A Model Handle Assembly Description GX-7 Model Handle AssemblyGX-7 DI Model Handle Assembly Description Qty GX-7 DI Model Handle AssemblyGX-7 400 Model Handle Assembly GX-7 400 Model Handle Assembly All models Coupling Block AssemblyGX-7A Mix Module Kit SpecificationsTip Set-Up Chart for GX-7A ModelModule Only Size Ref Module Kits Cleanout Drill Iso PortGX-7 400 Mix Module Kit Quantity In/mmTip Kits for GX-7 400 Gun No. Ref Quantity Set-up Chart for GX-7 400 ModelRound Spray Pattern GX-7 DI Model SpecificationsModule/Tip Data for Chemical Sprayed at 2500 PSI Output Pattern Lbs/minRound Tip Kits Size Quantity Tip KitsTool Kits For GX-7A and GX-7 DI ModelsCategory Data Technical DataGraco Standard Warranty