I.C.T.C. Holdings Corporation 1100NC For Excellent RESULTS, Read and Practice These Techniques

Page 10

The key to all good applications is a good spray gun technique. The finished results are what the client will look at and base his opinion on. Your skill and abilities are as important as good equipment and good paint. Proper application techniques can easily be learned by using the following simple guidelines. If you are not familiar with the basic spray techniques we recommend that you study this portion of the manual and practice the techniques shown. Practice your technique on scrap cardboard or old newspaper until you feel confident.

FOR EXCELLENT RESULTS, READ AND PRACTICE THESE TECHNIQUES

1.Always strain all paint through a H.E.R.O. strainer bag.

The most common reason for airless sprayers to malfunction is foreign matter jamming the valves or plugging the tip. Always strain the paint before putting through the pump.

2.Always spray at the lowest pressure setting which will provide a uniform spray fan. (fig. 1, page 10) Adjust pressure control knob so that paint is completely atomized . Insufficient pressure will result in "tailing". Too much pressure will result in excess fog and over spray, excess tip wear, and increased sprayer wear and tear. See setting up to spray, page 5.

3.Always spray at right angles to the surface being sprayed. (fig. 2, page 10)

Angling or arcing the nozzle toward the surface will cause uneven coverage and excessive overspray.

4.Always hold spray gun 12-15 inches from spray surface. (fig. 3, page 10)

Too close and the fan width will be reduced and material will be applied too heavily (runs).

Too far from the surface and you will have excessive overspray and light coverage (transparent).

5.Always move the gun parallel to the surface being sprayed, at a consistent speed. This avoids uneven coverage (thick or thin areas).

6.Always start the spray stroke before triggering the gun and release the trigger before completing the stroke. (fig. 4, page 10)

This avoids heavy build up of paint at either end of the spray stroke.

7.Always lap your spray pattern by one half. (fig. 5, page 10) This assures full coverage of the surface being painted.

AIRLESS SPRAY PAINTING

SUGGESTIONS AND TECHNIQUE

SPRAY TIP SELECTION

TIP SIZE

FOR APPLICATION OF

 

 

.021

Exterior Latex on large unobstructed areas. ( 60 OZ. )

H.E.R.O. INDUSTRIES

9

1100C & 1100NC OWNERS MANUAL

Image 10
Contents Page R.O. Warranty R.O. IndustriesTable of Contents Important Safety PrecautionsAlways R.O. Airless Spray Painting AlwaysSetting UP to Spray E R a T I N G InstructionsFlushing the Unit AT Shutdown or Color Change Special Notes General Maintenance Instructions Special Storage InstructionsAirless Spray Painting Suggestions and Technique SYSTEM, Even OvernightFor Excellent RESULTS, Read and Practice These Techniques 018 Troubleshooting Orifice SizeTroubleshooting Hydraulic Intake Valve REF# 59 Pressure Test Situation Electric Motor Wont START/RUNElectric Motor STALLS/QUITS No PRESSURE, Blue Hydraulic Fluid in PaintSprayer does not Prime with Paint Puddle of OIL Appearing Under Sprayer During OperationSpray Pattern Leaves Lines or Fingers Spray Pattern is Spotty or Uneven Diaphragm ReplacementExcessive Overspray or Fogging Replacement of Intake Seat REF # RemovalPiston Repairs Outgo Valve REF# Tools Required -1 wrenchREF# Pressure Control Valve Accessories Parts List O L SHOSE, Airless Paint 50 X 1/4 Parts List NEW Style BeginningOutgo Parts 45A TANK, Complete. Includes Ref# Drive Parts SPACER, 1100NC-MD only SPRING, 1100NC-MD only R.O. Industries1100MD Schematic Parts Schematics Authorized Sales and Service Centers U.S.A Authorized Sales and Service CENTERS- U.S.A Southern CaliforniaNEW York Rhode Island R.O. Industries 2719 Lake City WAY BURNABY, B.C Canada