I.C.T.C. Holdings Corporation Airless Spray Equipment, 1100C Hydraulic Intake Valve REF# 59

Page 14

movement causes a vacuum in the paint pump. This vacuum causes the intake valve to open, allowing a new supply of paint to enter. The corresponding paint outgo valve is drawn closed by the vacuum created by the diaphragm.

These operations are repeated at a rate of 750 times a minute. These continuously repeated actions draw paint into the pump, pressurize it, and then deliver it to the gun. The failure, of any one valve, to operate correctly will effect the overall equipment performance.

Each of the four valves mentioned earlier, have an important function and will effect the overall performance of the unit if not performing correctly.

HYDRAULIC INTAKE VALVE (REF# 59, PART # 4-30)

The hydraulic intake valve, is a small vacuum valve which controls the hydraulic oil entering the hydraulic pump/cylinder area. Once the oil has past through the valve it is prevented from returning. The valve is commonly called a “one way check valve”. Valve failure will result in the hydraulic pump being unable to build pressure, and the diaphragm will stop moving. Spray pressure will cease.

HYDRAULIC OUTGO VALVE (REF# 70, PART# 4-27C)

The hydraulic outgo valve, better known as the "pressure control valve", is used to control the units operating pressure. The valve is fully adjustable from 0 psi. to 3000 psi. By turning the pressure control valve knob (ref# 71) clockwise the pressure is increased. The hydraulic pump continues to build at all times and must have a means of releasing this pressure. Pressure applied to the P.C. ball, (ref# 84) will keep it lodged in the P.C. seat (ref# 83) until the internal hydraulic oil pressure is sufficient to cause it to open. The point at which the oil is released is equal to the level set by the control knob. As components within the pressure control valve wear, the valve looses its ability to maintain or reach the required pressures (see "low static pressure").

PAINT INTAKE VALVE ASSEMBLY (REF# 16-28)

The paint intake valve is made up of seven (7) items, endcap and seat (ref# 16 & 17), intake ball (ref# 18), cage (ref# 19) spring (ref# 20), O-ring (ref# 21), material head (ref# 22). The intake valve controls the incoming flow of spray materials and is responsible for keeping them from returning to the source. The ball must be able to create a complete seal on the seat, otherwise pressure will be lost. A worn intake valve may / will permit correct static pressure, but supply lower spray pressure. A worn intake ball will become smaller in diameter and loose its ability to seal at the seat. A worn seat will develop a large step in the area where contact with the ball is made. This can cause the intake ball to distort in shape making the ball egg shaped. If the valve assembly becomes warm to the touch, this may be a sign of a loose or worn seat caused by wear or washout / erosion. The intake seat is Lock-Tited into the endcap block. Over time the seat may become loose due to erosion of the metal. Replacement of a worn seat (ref# 17) is possible, see page 21. Replacement of the endcap, complete with seat is required if any signs of erosion is evident upon inspection.

PAINT OUTGO VALVE (REF# 32, PART# 4-11A)

The paint outgo valve monitors and controls the flow of spray materials as it leaves the sprayer. It also works together with the paint intake valve, to build paint pressure as specified by the setting made by the hydraulic outgo valve (pressure control valve). A worn outgo valve will result in pulsation in the spray material and cause the paint hose to jump and vibrate vigorously.

TROUBLESHOOTING

The solution to almost all problems can usually be found in the paint side valves. However, before performing any repair or looking further, the following are things which can cause an apparent sprayer failure, without any mechanical problem. ALWAYS check these items before preceding.

H.E.R.O. INDUSTRIES

13

1100C & 1100NC OWNERS MANUAL

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Page R.O. Warranty R.O. IndustriesTable of Contents Important Safety PrecautionsAlways R.O. Airless Spray Painting AlwaysSetting UP to Spray E R a T I N G InstructionsFlushing the Unit AT Shutdown or Color Change Special Notes General Maintenance Instructions Special Storage InstructionsAirless Spray Painting Suggestions and Technique SYSTEM, Even OvernightFor Excellent RESULTS, Read and Practice These Techniques 018 Troubleshooting Orifice SizeTroubleshooting Hydraulic Intake Valve REF# 59 Pressure Test Situation Electric Motor Wont START/RUNElectric Motor STALLS/QUITS No PRESSURE, Blue Hydraulic Fluid in PaintSprayer does not Prime with Paint Puddle of OIL Appearing Under Sprayer During OperationSpray Pattern Leaves Lines or Fingers Excessive Overspray or Fogging Diaphragm ReplacementSpray Pattern is Spotty or Uneven Replacement of Intake Seat REF # RemovalPiston Repairs Outgo Valve REF# Tools Required -1 wrenchREF# Pressure Control Valve Accessories Parts List O L SHOSE, Airless Paint 50 X 1/4 Parts List NEW Style BeginningOutgo Parts 45A TANK, Complete. Includes Ref# Drive Parts SPACER, 1100NC-MD only SPRING, 1100NC-MD only R.O. Industries1100MD Schematic Parts Schematics Authorized Sales and Service Centers U.S.A Authorized Sales and Service CENTERS- U.S.A Southern CaliforniaNEW York Rhode Island R.O. Industries 2719 Lake City WAY BURNABY, B.C Canada
Top Page Image Contents