Campbell Hausfeld AL2710 HOW to Flush, Important Components, Off, Procedure, Setting UP

Page 5
! WARNING
Wide Gap
Slight Gap
Figure 2 - PR Valve

Operating Instructions and Parts Manual

AL2710

Airless Paint Systems

Pre-Operation (Cont.)

is no pressure in the unit, and close the prime/pressure relief valve for storage.

Never leave pump

! WARNING unattended while it is under pressure!

6. START UP AFTER STORAGE: Before using water-base paint, flush with soapy water and then a clean water flush. Before using oil-base paint, flush out the mineral spirits with the material to be sprayed.

HOW TO FLUSH

IMPORTANT COMPONENTS

●Prime/Pressure Relief Valve (Prime/PR

Valve, Figure 2). Used to

relieve pressure from

gun, hose and tip and to

prime the unit when in OPEN

position. (It is in open position when there is a wider gap between valve handle and cam body.) When in CLOSED position, there is only a very slight gap between handle and body. When closed, the system is pressurized.

●Pressure Control Knob (Figure 3). Used to adjust

pressure. Turn Figure 3 - Pressure

clockwise to Control increase pressure and counterclockwise to decrease it.

●Toggle Switch (Figure 4).

ON

 

OFF

 

 

 

Figure 4 - Toggle Switch

PROCEDURE

1.Make sure the gun trigger lock is engaged and there is no spray tip in the gun. Refer to Figure 5. (Refer to Figure 10 for information on how to lock the trigger lock and the gun's safety features.)

Figure 5 - Engaging trigger lock

To reduce the risk of static sparking,

which can cause fire or explosion, always hold a metal part of the gun firmly against the grounded pail when flushing. (This also reduces splashing.)

2. Pour enough clean, compatible solvent into a large, empty pail to fill the pump and hoses.

3. Place the suction tube into the pail.

4. Turn the Prime/Pressure Relief (PR) Valve to the "OPEN" , priming position. Refer to Figure 3.

5. Point the gun into the pail and hold a metal part of the gun firmly against the pail. Refer to Figure 6.

Figure 6 - Holding gun against pail

6.Disengage the gun safety latch and squeeze the gun trigger. Turn the

ON-OFF Toggle Switch to the "ON" position (Figure 4) and turn Pressure Control Knob (Figure 3) clockwise to increase pressure just enough to start the pump.

7.Turn the Prime/PR Valve to the "CLOSED" position. This will allow solvent to be flushed through the pump, hoses and gun. Allow the unit to operate until clean solvent comes from the gun.

8.Release the trigger and engage the gun trigger lock.

9.If you are going to start spraying, place the suction tube into the supply container. Release the gun safety latch and trigger the gun into another empty, metal container, holding a metal part of the gun firmly against the pail and force the solvent from the pump and hose. Engage the gun safety latch until you are ready to spray.

10.If you are going to store the sprayer, remove the suction tube from the solvent pail, holding a metal part of the gun firmly against the pail and force the solvent from the pump and hose. Engage the gun safety latch. Refer to "Storage" Procedure on page 4.

11.Whenever you shut off the sprayer, follow the "PRESSURE RELIEF PROCEDURE" on page 3.

SETTING UP

1.Connect the hose and gun.

a.Remove the plastic cap plug from the outlet tee and screw a conductive or grounded 3000 psi airless spray hose onto fluid outlet.

b.Connect an airless spray gun to the other end of the hose.

www.chpower.com

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Operating Instructions and Parts Manual AL2710Specifications Table of ContentsSafety Guidelines General Safety InformationSkin Injection Hazard Electrical Shock HazardFire or Explosion Hazard Pre-OperationFlushing Amperage Length of Cord Ft RatingProcedure HOW to FlushSetting UP Important ComponentsSpray TIP Selection OperationStarting UP Tip Selection Chart Spray Technique Electrical SystemElectrical Board Calibration Zero CalibrationLiquid Crystal Display LCD Calibration Electrical TroubleshootingPressure Calibration Spray GUN ServiceReplacement of Electrical Components Gear and Pump Assembly Fluid Pump ReinstallationReplacing Valve Spring Unit Fluid PumpMaintenance Reassembly Symptom Possible Causes Corrective Action Troubleshooting ChartPossible Cause Corrective Action Electrical TroubleshootingAL2710 Spray Gun For Replacement Parts, CallAL2710 Spray Gun Ref. No Description Part Number Qty Parts List for Spray Gun for use with AL2710Airless Paint Sprayer Model AL2710 Not applicable Parts List for Airless Paint Sprayer, Model AL2710Electrical System Ref. No Description Part Number Qty Parts List for Electrical SystemAL2710 111-200-99 Ref. No Description Part Number Qty Manifold Filter Parts List for Manifold FilterPiston Rod and Upper Check Valve Parts List for Piston Rod, Upper Check ValveLower Suction Valve Parts List for Lower Suction Valve Gear and Pump Assembly Parts List for Gear and Pump Assembly 331-236 Ref. No Description Part Number Qty Parts List for Fluid PumpResponsibilities of Purchaser Under this Warranty What is not Covered Under this Warranty

AL2710 specifications

The Campbell Hausfeld AL2710 is a versatile and efficient air compressor, designed to meet the demands of both DIY enthusiasts and professional users. With a compact design and a range of powerful features, this compressor stands out in its category for its reliability and performance.

One of the key features of the AL2710 is its 1.5 HP motor, which provides consistent and powerful airflow. It operates at a maximum pressure of 125 PSI, making it suitable for a variety of applications, from inflating tires and powering air tools to providing air assistance for painting and finishing tasks. The compressor has a tank capacity of 3.5 gallons, enabling it to store enough air for extended use without frequent cycling.

The AL2710 is built with portability in mind. Weighing just over 40 pounds, it comes with an ergonomic handle and a lightweight design that allows for easy transportation to various job sites. Its low-profile design not only enhances mobility but also makes it easy to store in tight spaces.

Another notable characteristic is its oil-free pump, which significantly reduces maintenance requirements. This technology not only contributes to a cleaner operation but also enhances the compressor's lifespan. Users can benefit from the convenience of not needing to deal with oil changes, allowing them to focus more on their work.

The unit features a quick-connect coupler for rapid tool changes, enhancing productivity. Additionally, the integrated pressure gauge enables users to monitor air pressure levels with ease, ensuring optimal performance of their air-powered tools.

Noise levels are also a consideration for many users. The Campbell Hausfeld AL2710 operates at a relatively low noise level, making it suitable for use in residential areas or noise-sensitive environments.

In summary, the Campbell Hausfeld AL2710 air compressor is defined by its powerful and portable design, oil-free operation, and user-friendly features. It is an ideal choice for those who need a reliable compressor for various tasks, combining efficiency, durability, and ease of use. Whether for home improvement projects or professional applications, the AL2710 provides the necessary performance to get the job done effectively.
Top Page Image Contents