Campbell Hausfeld AL2710 Pre-Operation, Fire or Explosion Hazard, Flushing, 150 200 250

Operating Instructions and Parts Manual AL2710

Airless Paint Systems

General Safety Information (Cont.)

●Do not use pliers to tighten or loosen high pressure connections.

●Motor is equipped with an automatic thermal overload. Motor will restart without warning, after cooling.

	Never aim or
! WARNING
	spray at yourself

or anyone else or serious injury could occur.

!WARNING

FIRE OR EXPLOSION HAZARD:

●Do not use solvents with flash points less than 70°F (21°C) to clean this equipment (examples of acceptable cleaning solvents are water, mineral spirits, lacquer thinner, Xylene and high flash napha. A partial example list of unacceptable cleaning solvents are low flash napha, mek, acetone, alcohol and toluene).

! WARNING

Do not spray flammable materials in vicinity of open flame or near

ignition sources. Motors, electrical equipment and controls can cause electrical arcs that will ignite a flammable gas or vapor. Never store flammable liquids or gases in the vicinity of the unit.

Do not spray acids,

!WARNING corrosive materials, toxic chemicals, fertilizers or pesticides. Using these materials could result in death or serious injury.

●Paints and solvents containing HALOGENATED HYDROCARBONS can react explosively with aluminum. Do not use halogenated hydrocarbons with this equipment. Consult the paint or solvent product label or Material Safety Data Sheets (MSDS) to help determine if it contains halogenated hydrocarbons.

●Do not use fuels to clean this equipment.

●Keep spraying area well ventilated. Keep doors and windows open.

●Remove all ignition sources (i.e. Static electricity, pilot lights, cigarettes and electrical arcing).

●Airless spraying can cause static electricity. Always ground the pump and spraying surface. Always use a 3-wire grounded extension cord and power receptacle.

●Do not use solvents containing halogenated hydrocarbons.

Keep hose away

! CAUTION from sharp objects. Bursting hoses may cause injury. Examine hoses regularly and replace if damaged.

●Check hoses for weak or worn condition before each use, making certain that all connections are secure.

Pre-Operation

FLUSHING

1.NEW SPRAYER: Your sprayer was

factory tested in an oil solution which was left in the pump. Before using oil- based paint, flush with mineral spirits only.Before using water-based paint flush with mineral spirits, followed by soapy water, then a clean water flush.

2.CHANGING COLORS: Flush with a compatible solvent such as mineral spirits or water.

3.CHANGING FROM WATER-BASED TO OIL-BASED PAINT: Flush with soapy water, then mineral spirits.

4.CHANGING FROM OIL-BASED TO WATER-BASED PAINT: Flush with mineral spirits, followed by soapy water, then a clean water flush.

5.STORAGE: Always relieve pressure (See pressure relief procedure on page 3) prior to storage or when machine is unattended. Follow the storage procedure based on the kind of paint you used:

●Oil-based paint: Flush with mineral spirits. Make sure that there is no pressure in the unit. Then close the prime/pressure relief valve.

●Water-based paint: Flush with water, then mineral spirits. For longer term storage use a 50/50 mixture of mineral spirits and motor oil. Always ensure that there

Extension Cord Requirements

Amperage						Length of Cord (Ft.)
Rating		25	50	100	150	200	250	300	400	500
											G
5	- 6	18	16	12	12	10	10	8	8	6
											A
6	- 8	18	16	12	10	10	8	6	6	6
											U
8 - 10		18	14	12	10	8	8	6	6	4
											G
10	- 12	16	14	10	8	8	6	6	4	4	E

Table 1 - Extension Cord Gauges

www.chpower.com

4