Grizzly G0755 owner manual Machine Data Sheet

Page 6

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0755 HEAVY-DUTY MILL/DRILL WITH STAND AND

POWER FEED

Product Dimensions:
Weight	992 lbs.
Width (side-to-side) x Depth (front-to-back) x Height	49-1/2 x 34-1/2 x 75-1/4 in.
Footprint (Length x Width)	29 x 21 in.
Space Required for Full Range of Movement (Width x Depth)	68 x 34 in.
Shipping Dimensions:
Type	Wood Crate
Content	Machine
Weight	1102 lbs.
Length x Width x Height	49 x 36-3/4 x 80-3/4 in.
Must Ship Upright	Yes
Electrical:
Power Requirement	220V, Single-Phase, 60 Hz
Prewired Voltage	220V
Full-Load Current Rating	8.6A
Minimum Circuit Size	15A
Connection Type	Cord & Plug
Power Cord Included	Yes
Power Cord Length	6 ft.
Power Cord Gauge	14 AWG
Plug Included	No
Recommended Plug Type	6-15
Switch Type	Magnetic Switch w/Overload Protection
Motors:
Main
Type	TEFC Capacitor-Start Induction
Horsepower	2 HP
Phase	Single-Phase
Amps	8.6A
Speed	1725 RPM
Power Transfer	Gear Drive
Bearings	Shielded & Permanently Lubricated
Elevation
Type	TEFC Capacitor-Start Induction
Horsepower	1/8 HP
Phase	Single-Phase
Amps	0.75A
Speed	1725 RPM
Power Transfer	Gear Drive
Bearings	Shielded & Permanently Lubricated

-4-	Model G0755 (Mfg. Since 1/13)

Image 6

Contents Model G0755 Page Table of Contents Introduction Machine Description Manual AccuracyContact Info Identification Machine Data Sheet Table Info Safety Safety Instructions for MachineryPage Additional Safety for Mill/Drills Full-Load Current Rating Power SupplyAvailability Circuit Requirements forMinimum Gauge Size 14 AWG Grounding InstructionsExtension Cords 50 ftSetup Needed for SetupUnpackingInventory Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Lifting & Placing To move your machine into positionAnchoring to Floor Assembly Anchoring to Concrete FloorsMachine Base Concrete Joining Drill Chuck Arbor Lubricating Mill/DrillTo join the drill chuck and arbor Test Run To test run the machineInspections Adjustments Spindle Break-InOperations Operation OverviewControl Panel Downfeed Controls Using Coarse DownfeedUsing Fine Downfeed IdentificationDepth Stop Headstock MovementRaising/Lowering Headstock Table Travel Tilting HeadstockGraduated Dials Axis Power Feed ON/OFF SwitchAxis Handwheels To install tool holder Installing/Removing ToolingInstalling Tool Holder Tool Needed QtyDetermining Spindle Speed Spindle SpeedRemoving Tool Holder Tools Needed QtySetting Spindle Speed Spindle Speed Range Lever Speed LeverAccessories ISO 68 and ISO 32 machine oilH7527-6 Rotary Table Set H7527 6 Rotary Table SetG5641-1-2-3 Blocks G9815-Parallel Set G9612-Test IndicatorG5774-R-8 End Mill Holder Set H5930-4-Pc Center Drill Set H5931-4-Pc Center Drill SetSchedule MaintenanceCleaning Protecting LubricationHeadstock Reservoir To change the headstock oilBall Oilers Table/Column Ways & QuillTable Leadscrews Quill Rack & PinionAxis Leadscrew Service TroubleshootingSymptom Possible Cause Possible Solution Adjusting Gibs Adjusting Leadscrew BacklashTramming Spindle To tram the spindle with the tableReplacing Power Feed Carbon Brushes To adjust the return spring tension Tightening Return Spring TensionWiring Wiring Safety InstructionsElectrical Box Wiring Control PanelMotors & Other Electrical Wiring Axis Motor Axis Limit Switch Electrical PhotosElectrical Box Control Panel Rear View Spindle MotorParts HeadHead Parts List DescriptionDescription Table & Column Table & Column Parts List Electrical Components 401 406 402 403 405 404 415 411 408 407 409 412 410 413 414Power Feed Accessories Machine Labels & Cosmetics Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns