Black & Decker 90504614 Operating Instructions, Trigger Switch & Forward/Reverse Button Figure B

Page 7

90504614 SC1400 Lith Ion drill 6/19/06 9:49 AM Page 7

3.While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem.

4.If the batteries do not charge properly—(1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and tool to a surrounding air temperature of 40°F (4,5 °C) to 105°F (+40,5 °C). (4) If the receptacle and temperature are OK, and you do not get proper charging, take or send the tool and charger to your local Black & Decker service center. See Tools Electric in yellow pages.

5.The tool should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its batteries in a depleted condition.

Operating Instructions

Trigger Switch & Forward/Reverse Button - Figure B

•The drill is turned ON and OFF by pulling and releasing the trigger switch (3).

•The farther the trigger is depressed, the higher the speed of the drill.

•A forward / reverse control button (4) determines the direction of the tool and also serves as a lock off button.

•To select forward rotation, release the trigger switch and depress the forward / reverse control button to the left.

•To select reverse, depress the forward / reverse control button the opposite direction.

•The center position of the control button locks the tool in the off position. When changing the position of the control button, be sure the trigger is released.

B

4

3

NOTE: Under heavy loads the drill may cut out as a safety precaution. If this happens, release the trigger switch and squeeze it again to start the drill.

Torque Control - Figure C

This tool is fitted with a collar to select the operating mode and to set the torque for tightening screws. Large screws and hard workpiece materials require a higher torque setting than small screws and soft workpiece materials.

•For drilling in wood, metal and plastics, set the adjustable torque collar (2) to the drilling position symbol

.

•For screwdriving, set the adjustable torque collar (2) to the desired setting. If you do not yet know the appropriate setting, proceed as follows:

C

2

•Set the collar to the lowest torque setting.

•Tighten the first screw.

•If the clutch ratchets before the desired result is achieved, increase the collar setting and continue tightening the screw. Repeat until you reach the correct setting. Use this setting for the remaining screws.

Dual Range Gearing - Figure D

The dual range feature (5) of your drill allows you to shift

gears for greater versatility.

D

•To select low speed, high torque setting (position 1), turn tool off and permit to stop. Slide gear shifter button (5) away from the chuck.

• To select the high speed, low torque setting (position 2),

5

turn tool off and permit to stop. Slide gear shifter button

 

towards the chuck.

 

NOTE: Do not change gears when tool is running. If you are having trouble changing gears, make sure that the dual

range gear button is either completely pushed forward or completely pushed back.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents VEA EL Español EN LA Contraportada Catalog Number SC1400General Safety Rules 90504614 SC1400 Lith Ion drill 6/19/06 949 AM Safety Guidelines / Definitions Specific Safety RulesSafety Warnings and Instructions Charging Safety Warnings and Instructions BatteriesFunctional Description Important Charging Notes Charging ProcedureDual Range Gearing Figure D Trigger Switch & Forward/Reverse Button Figure BOperating Instructions Torque Control Figure CDrilling in Wood Battery Level Indicator Figure FScrew Driving DrillingDrilling in Masonry TroubleshootingMaintenance Drilling in MetalService Information AccessoriesFull TWO-YEAR Home USE Warranty Mode D’EMPLOI Conserver CES Directives Règles de sécurité générales90504614 SC1400 Lith Ion drill 6/19/06 950 AM Conserver CES Directives Règles DE Sécurité SpécifiquesDescription fonctionnelle Avertissements de sécurité et directives bloc-pilesAvertissements de sécurité et directives chargement Procédure de chargeCorrecteur de couple figure C FonctionnementRemarques importantes de chargement Détente et bouton de marche avant/marche arrière figure BVissage Engrenage à deux vitesses figure DMandrin sans clé figure E Indicateur de niveau de charge figure FEntretien AccessoiresLE Sceau Rbrcmc Problème Cause possible Dépannage555326-7100 Conserve Estas Instrucciones Normas generales de seguridad90504614 SC1400 Lith Ion drill 6/19/06 950 AM Conserve Estas Instrucciones Normas DE Seguridad EspecíficasDescripción de las Funciones Instrucciones y advertencias de seguridad carga Instrucciones y advertencias de seguridad BateríasInterruptor disparador y botón de avance/reversa Figura B Procedimiento de cargaInstrucciones de operación Notas importantes sobre la cargaIndicador del nivel de carga de la batería Figura F Control de torsión Figura CEngranaje de doble alcance Figura D Portabrocas sin llave Figura ETaladrado en metal DestornilladoTaladrado Taladrado en maderaInformación DE Mantenimiento MantenimientoPUEBLA, PUE Garantía Completa DE DOS Años Para USO EN EL HogarCULIACAN, SIN MONTERREY, N.L GUADALAJARA, JAL90504614 SC1400 Lith Ion drill 6/19/06 950 AM 90504614 SC1400 Lith Ion drill 6/19/06 950 AM 90504614 SC1400 Lith Ion drill 6/19/06 950 AM

90504614 specifications

The Black & Decker 90504614 is a high-performing power tool accessory designed to enhance the efficiency and precision of your woodworking and construction projects. This product features a range of attributes that make it a reliable choice for both professionals and DIY enthusiasts alike.

One of the standout features of the 90504614 is its exceptional durability. Constructed with premium materials, it is engineered to withstand heavy usage and resist wear and tear. This durability ensures that users can rely on the tool for a long duration without experiencing significant degradation in performance. The rugged design is complemented by its lightweight build, making it easy to handle and maneuver, even in tight spaces.

Another characteristic that sets the Black & Decker 90504614 apart is its user-friendly design. It is compatible with a variety of Black & Decker power tools, allowing for seamless integration into your existing toolkit. This versatility means that you can easily switch between different tasks without needing to invest in multiple accessories. This adaptability is particularly beneficial for users who frequently tackle a wide range of projects.

Technologically, the 90504614 incorporates advanced engineering that enhances its cutting precision. Its sharp, high-strength blades are designed to provide clean cuts, reducing the need for post-processing and improving overall workflow. The tool is also equipped with features that minimize vibration, allowing for steadier operation and increased accuracy during use. This is particularly valuable for intricate tasks that demand high levels of concentration and finesse.

Moreover, safety is a paramount concern in power tool design, and the Black & Decker 90504614 delivers in this aspect too. It includes built-in safety features that help prevent accidents, making it suitable for users of varying skill levels. This focus on safety not only protects the user but also extends the lifespan of the tool itself.

In conclusion, the Black & Decker 90504614 is an impressive accessory that combines durability, versatility, cutting precision, and safety. Its thoughtful engineering makes it an excellent choice for anyone looking to enhance their toolkit with a reliable and efficient power tool accessory. Whether tackling home improvement projects or professional builds, the 90504614 is sure to meet and exceed user expectations.
Top Page Image Contents