Bosch Power Tools 11316EVS manual Operating Instructions

Page 7

BM 1619929470 2-05 2/18/05 12:02 AM Page 7

Operating Instructions

SLIDE "ON-OFF" SWITCH

The tool is switched "ON" by the slide switch 9 located in the rear handle.

TO TURN THE TOOL "ON" slide the switch to the right.

TO TURN THE TOOL"OFF " slide the switch to the left.

VARIABLE SPEED DIAL

Your tool is equipped with a variable speed dial. The impact rate (BPM) and rotating speed (RPM) can be varied according to the type of work being performed by setting the variable speed dial to the selected setting. The chart below will help you to determine which setting to use for your application. However, a pre-test will determine the best speed setting, as the chart is intended only as a guide. Once the proper setting is determined the impact rate and rotating speed is kept constant by means of the "Electronic Feedback Circuitry". The variable speed dial can be adjusted while the motor is running with the tool free from work, allowing the operator to adjust the impact rate and rotating speed according to the actual application.

CHIPPING (DEMOLITION)

Area of application

Control setting

 

 

Plaster work

1 - 2

Removing tiles

3

Brick work

4

Concrete

5 - 6

 

 

ELECTRONIC FEEDBACK CIRCUITRY

(EFC)

The internal electronic feedback system provides a "soft start", which will reduce the stresses that occur from a high torque start. The system also helps to keep the pre-selected impact rate and rotating speed virtually constant between no-load and load conditions.

INSTALLING ACCESSORIES

Clean the insert shank end of the accessory to remove any debris, then lightly grease with a light oil or lubricant.

Insert accessory into the tool holder through the dust shield, while twisting and pushing inward until it locks automatically into place.

Pull outward on the accessory to be certain it is locked into the tool holder (Fig. 2).

NOTE: The high efficiency available from the rotary hammers can only be obtained if sharp and undamaged accessories are used. The "cost" to maintain sharp and undamaged accessories is more than offset by the "time saved" in operating the tool with sharp accessories.

REMOVING ACCESSORIES

Accessories may be hot ! WARNING after use. Avoid contact with

skin and use proper protective gloves or cloth to remove.

To remove an accessory, pull and hold locking sleeve backward and pull bit forward. All accessories should be wiped clean after removing.

FIG. 2

LOCKING SLEEVE

"VARIO-LOCK"- SELECTOR RING

The vario-lock selector ring can be set in any one of twelve (30˚ increments) positions. Choose a position which is best suited for your operation. To adjust, pull the selector ring forward and hold firmly, then turn both the accessory and the selector ring to the desired position. Release the selector ring and turn the accessory slightly until it locks in place.

-7-

Image 7
Contents See For English Parlez-vous français?Work Area Power Tool Safety RulesElectrical Safety Personal SafetyService Demolition Hammer Safety RulesJob better and safer at the rate for which it is designed Accessories may be hot after prolonged use Symbols Model number 11316EVS Shank style SDS Max Functional Description and SpecificationsDemolition Hammer Measures reduce the risk of starting the tool accidentallyOperating Instructions Tool Tips Auxiliary HandleAccessories MaintenanceCleaning Sécurité des personnes Règles de Sécurité GénéralesAire de travail Sécurité électriqueRéparation Consignes de sécurité pour le marteau de démolitionInterrupteur est dangereux et doit être réparé Le plomb provenant des peintures à base de plomb Symboles Type de tige Description fonctionnelle et spécificationsMarteau de démolition Numéro de modèleConsignes de fonctionnement Conseils Pratiques Poignée AuxiliaireEntretien AccessoiresNettoyage Seguridad personal Normas de seguridad para herramientas mecánicasArea de trabajo Seguridad eléctricaServicio Normas de seguridad para martillos de demoliciónBM 1619929470 2-05 2/18/05 1202 AM Con aislamiento doble SímbolosDe Ni-Cd Número de modelo Descripción funcional y especificacionesMartillo de demolición Riesgo de arrancar la herramienta accidentalmenteInstrucciones de funcionamiento Consejos Para LA Herramienta Mango AuxiliarAccesorios MantenimientoLimpieza BM 1619929470 2-05 2/18/05 1202 AM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools