Ryobi TS1350 warranty To Install Blade

Page 14

ASSEMBLY

TO INSTALL BLADE

See Figures 15 and 16.

WARNING:

A 10 in. (254 mm) blade is the maximum blade capacity of your saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guards, while thicker blades will prevent the blade bolt from securing the blade on the spindle. Either of these situa- tions could result in a serious accident and can cause serious personal injury.

■Unplug your saw.

WARNING:

Failure to unplug your saw could result in accidental starting causing possible serious personal injury.

■ Insert the wrench provided through slot in lower blade

guard bracket and loosen screw A, securing the blade

bolt cover, approximately one-half turn.

■ Rotate lower blade guard and remove screw B. Rotate

blade bolt cover up and back to expose the blade bolt.

■ Push down on the saw arm and pull out the lock pin to

release saw arm. Raise saw arm to its full raised posi-

tion. Be cautious, saw arm is spring loaded to raise.

■ Depress the spindle lock button and rotate the blade

bolt until the spindle locks.

■ Using the wrench provided, loosen and remove the blade

bolt.

SPINDLE LOCK

BUTTON

 

 

 

 

Fig. 15

ROTATE SAW ARM DOWN

ROTATE SAW ARM UP

TO EXPOSE SCREW A

TO EXPOSE SCREW B

SLOT

SCREW A

SCREW B

 

 

 

 

securely.

 

 

 

 

blade

 

 

 

lower

screw

 

 

 

use

 

 

 

and

 

 

 

guardtightenbefore

 

 

Restore

 

 

Note: The blade bolt has left hand threads. Turn blade

bolt clockwise to loosen.

■ Remove outer blade washer. Do not remove inner blade

washer.

■ Wipe a drop of oil onto inner blade washer and outer

blade washer where they contact the blade.

WARNING:

If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly.

■Fit saw blade inside lower blade guard and onto spindle. The blade teeth point downward at the front of saw as shown in figure 16.

■Replace outer blade washer. The double "D" flats on the blade washers align with the flats on the spindle.

■Depress spindle lock button and replace blade bolt.

LOWER

BLADE GUARD

TO

LOOSEN

TO

TIGHTEN

BLADE BOLT

Restore lower blade guard and securely tighten screw before use.

INNER BLADE

WASHER WITH

DOUBLE "D" FLATS

BLADE

OUTER BLADE WASHER WITH DOUBLE "D" FLATS

Fig. 16

Page 14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Save this Manual for Future Reference Thank YOU for Buying a Ryobi Compound Miter SAWIntroduction Table of ContentsProduct Specifications Double Insulation Symbol MeaningRules for Safe Operation Read ALL Instructions Before Making a CUT, be sure all adjustments are secure Glossary of Terms for Woodworking FreehandCombination Square UnpackingTools Needed Framing SquareWork Clamp Miter Lock Handle Loose Parts ListDust BAG Stop BlockCutting Capacities FeaturesKnow Your Compound Miter SAW AMP MotorSpindle Lock Button Carrying HandleMiter Lock Handle Trigger Lock Electric Brake Positive Stops on Miter Table Bevel Lock Knob Miter FenceDust BAG AssemblyDust Guide Work ClampClamp Bracket Bracket Screw Small Stop Block Table ExtensionsStop Block Wing Screw Extension Miter SAW BaseTo Install Blade Framing Square Miter Fence Miter Table Squaring the Miter Table to the FenceSee Figures 17 Miter Lock Handle View of Miter Table Square with FenceAdjustments Miter Fence Miter TableMiter Fence Squaring the SAW Blade to the FenceSee Figures 21 Blade Miter Framing Table SquareBlade Squaring the Blade to the Miter TableSee Figures 25 Combination Miter SquareCutting a Slot in the Zero Clearance Throat Plate Pivot Adjustments Travel Pivot AdjustmentBevel Pivot Adjustment Depth StopCrosscutting OperationCutting with Your Compound Miter SAW To Crosscut with Your Miter SAWSee Figures 30 Bevel CUT Indicator PointBevel CUT Mounting BracketCompound Miter CUT Compound Miter CUTTo Make a Compound CUT with Your Miter SAW Long Workpiece Support Long WorkpiecesJamming the blade. See Figures 36 Workpiece SupportsCOMPOUND-ANGLE Settings for Popular Structures Cutting Compound MitersCutting Crown Molding Laying Molding Flat on the Miter TableRight Cutting Warped MaterialClamping Wide Workpieces WrongLubrication MaintenanceGeneral Extension CordsOperators Manual Ryobi TECHNOLOGIES, INC
Top Page Image Contents