Ryobi TS1350 warranty Squaring the Miter Table to the Fence, See Figures 17

Page 15

ASSEMBLY

CAUTION:

Always install the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw. The direction of blade rotation is also stamped with an arrow on the upper blade guard.

Note: The blade bolt has left hand threads. Turn blade bolt counterclockwise to tighten.

■Tighten blade bolt securely.

■Replace the lower blade guard and blade bolt cover.

■Replace screw B and tighten securely.

■Retighten screw A securely.

■Remove the blade wrench.

WARNING:

Make sure the spindle lock button is not engaged before reconnecting saw into power source. Never engage spindle lock button when blade is rotating.

Your compound miter saw has been adjusted at the factory for making very accurate cuts. However, some of the com- ponents might have been jarred out of alignment during shipping. Also, over a period of time, readjustment will probably become necessary due to wear. After unpacking your saw, check the following adjustments before you begin using saw. Make any readjustments that are necessary and periodically check the parts alignment to make sure that your saw is cutting accurately.

WARNING:

Your saw should never be connected to power supply when you are assembling parts, making adjustments, installing or removing blades, or when not in use.

Disconnecting your saw will prevent accidental starting that could cause serious injury.

Note: Many of the illustrations in this manual show only portions of your compound miter saw. This is intentional so that we can clearly show points being made in the illustra- tions. Never operate your saw without all guards securely in place and in good operating condition.

SQUARING THE MITER TABLE TO THE FENCE

See Figures 17 - 20.

■Unplug your saw.

FRAMING

SQUARE

MITER

FENCE

MITER TABLE

MITER

ZERO CLEARANCE

LOCK PLATE

THROAT PLATE

MITER

LOCK HANDLE

VIEW OF MITER TABLE SQUARE WITH FENCE

Fig. 17

Page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Thank YOU for Buying a Ryobi Compound Miter SAW Save this Manual for Future ReferenceTable of Contents Product SpecificationsIntroduction Symbol Meaning Rules for Safe OperationDouble Insulation Read ALL Instructions Before Making a CUT, be sure all adjustments are secure Freehand Glossary of Terms for WoodworkingFraming Square UnpackingTools Needed Combination SquareStop Block Loose Parts ListDust BAG Work Clamp Miter Lock HandleAMP Motor FeaturesKnow Your Compound Miter SAW Cutting CapacitiesTrigger Lock Carrying HandleMiter Lock Handle Spindle Lock ButtonMiter Fence Positive Stops on Miter TableBevel Lock Knob Electric BrakeWork Clamp AssemblyDust Guide Dust BAGWing Screw Extension Miter SAW Base Table ExtensionsStop Block Clamp Bracket Bracket Screw Small Stop BlockTo Install Blade Miter Lock Handle View of Miter Table Square with Fence Squaring the Miter Table to the FenceSee Figures 17 Framing Square Miter Fence Miter TableMiter Fence Miter Table AdjustmentsBlade Miter Framing Table Square Squaring the SAW Blade to the FenceSee Figures 21 Miter FenceCombination Miter Square Squaring the Blade to the Miter TableSee Figures 25 BladeDepth Stop Pivot Adjustments Travel Pivot AdjustmentBevel Pivot Adjustment Cutting a Slot in the Zero Clearance Throat PlateTo Crosscut with Your Miter SAW OperationCutting with Your Compound Miter SAW CrosscuttingMounting Bracket Bevel CUT Indicator PointBevel CUT See Figures 30Compound Miter CUT To Make a Compound CUT with Your Miter SAWCompound Miter CUT Workpiece Supports Support Long WorkpiecesJamming the blade. See Figures 36 Long WorkpieceCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresLaying Molding Flat on the Miter Table Cutting Crown MoldingWrong Cutting Warped MaterialClamping Wide Workpieces RightExtension Cords MaintenanceGeneral LubricationRyobi TECHNOLOGIES, INC Operators Manual
Top Page Image Contents