Ryobi TS1350 warranty Unpacking, Tools Needed, Combination Square, Framing Square

Page 7

UNPACKING

Your Compound Miter Saw has been shipped completely assembled except for the blade, miter lock handle, dust guide or dust bag, table extensions, and stop block.

■Remove all loose parts from the carton. Separate and check with the list of loose parts. See Figure 1.

■Remove the packing materials from around your saw.

■Carefully lift saw from the carton by the carrying handle and place it on a level work surface. Although small, this saw is heavy. To avoid back injury, get help when needed.

■Do not discard the packing materials until you have carefully inspected the saw, identified all loose parts, and satisfactorily operated your new saw.

■Your saw has been shipped with the saw arm secured in the down position. To release the saw arm, push down on top of saw arm and cut the tie-wrap.

■Lift the saw arm by the handle. Hand pressure should remain on the saw arm to prevent sudden rise upon release of the tie wrap.

■Examine all parts to make sure no breakage or damage has occurred during shipping.

If any parts are damaged or missing, do not attempt to plug in the power cord and turn the switch on until the damaged or missing parts are obtained and are installed correctly.

WARNING:

If any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury.

TOOLS NEEDED

The following tools (not included) are needed for checking adjustments of your saw or for installing the blade:

10 mm COMBINATION WRENCH

COMBINATION

SQUARE

8 mm HEX KEY

FRAMING SQUARE

Page 7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Thank YOU for Buying a Ryobi Compound Miter SAW Save this Manual for Future ReferenceProduct Specifications Table of ContentsIntroduction Rules for Safe Operation Symbol MeaningDouble Insulation Read ALL Instructions Before Making a CUT, be sure all adjustments are secure Freehand Glossary of Terms for WoodworkingFraming Square UnpackingTools Needed Combination SquareStop Block Loose Parts ListDust BAG Work Clamp Miter Lock HandleAMP Motor FeaturesKnow Your Compound Miter SAW Cutting CapacitiesTrigger Lock Carrying HandleMiter Lock Handle Spindle Lock ButtonMiter Fence Positive Stops on Miter TableBevel Lock Knob Electric BrakeWork Clamp AssemblyDust Guide Dust BAGWing Screw Extension Miter SAW Base Table ExtensionsStop Block Clamp Bracket Bracket Screw Small Stop BlockTo Install Blade Miter Lock Handle View of Miter Table Square with Fence Squaring the Miter Table to the FenceSee Figures 17 Framing Square Miter Fence Miter TableMiter Fence Miter Table AdjustmentsBlade Miter Framing Table Square Squaring the SAW Blade to the FenceSee Figures 21 Miter FenceCombination Miter Square Squaring the Blade to the Miter TableSee Figures 25 BladeDepth Stop Pivot Adjustments Travel Pivot AdjustmentBevel Pivot Adjustment Cutting a Slot in the Zero Clearance Throat PlateTo Crosscut with Your Miter SAW OperationCutting with Your Compound Miter SAW CrosscuttingMounting Bracket Bevel CUT Indicator PointBevel CUT See Figures 30To Make a Compound CUT with Your Miter SAW Compound Miter CUTCompound Miter CUT Workpiece Supports Support Long WorkpiecesJamming the blade. See Figures 36 Long WorkpieceCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresLaying Molding Flat on the Miter Table Cutting Crown MoldingWrong Cutting Warped MaterialClamping Wide Workpieces RightExtension Cords MaintenanceGeneral LubricationRyobi TECHNOLOGIES, INC Operators Manual
Top Page Image Contents