Ryobi TS1350 warranty Adjustments, Miter Fence Miter Table

Page 16

ADJUSTMENTS

WARNING:

Failure to unplug your saw could result in accidental starting causing possible serious personal injury.

■Push down on the saw arm and pull out the lock pin to release the saw arm.

■Raise saw arm to its full raised position.

■Loosen the miter lock handle approximately one-half turn.

■Depress the miter lock plate and rotate the miter table until the pointer on the control arm is positioned at 0° .

■Release the miter lock plate and securely tighten the miter lock handle.

■Lay a framing square flat on the miter table. Place one leg of the square against the fence. Place the other leg of the square beside the zero clearance throat plate in the miter table. The edge of the square and the zero clearance throat plate in the miter table should be paral- lel as shown in figure 19.

■If the edge of the framing square and the zero clearance throat plate in the miter table are not parallel as shown in figures 18 and 19, adjustments are needed.

■Loosen the socket head screws securing the fence. See Figure 20. Adjust the fence left or right until the framing square and zero clearance throat plate are parallel.

■Retighten the screws securely and recheck the fence- to-table alignment.

MITER FENCE

MITER TABLE

FRAMING

ZERO CLEARANCE

SQUARE

THROAT PLATE

VIEW OF MITER TABLE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED

Fig. 18

MITER

FENCE

MITER TABLE

FRAMING

ZERO CLEARANCE

SQUARE

THROAT PLATE

VIEW OF MITER TABLE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED

Fig. 19

SOCKET HEAD

SCREW(S)

FENCE

4 5

3

 

1.6

30

 

2

2.5

15

 

 

SOCKET HEAD

SCREW(S)

4

5

 

 

.6

30

31

 

22.5

0

15

 

Fig. 20

Page 16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Save this Manual for Future Reference Thank YOU for Buying a Ryobi Compound Miter SAWProduct Specifications Table of ContentsIntroduction Rules for Safe Operation Symbol MeaningDouble Insulation Read ALL Instructions Before Making a CUT, be sure all adjustments are secure Glossary of Terms for Woodworking FreehandUnpacking Tools NeededCombination Square Framing SquareLoose Parts List Dust BAGWork Clamp Miter Lock Handle Stop BlockFeatures Know Your Compound Miter SAWCutting Capacities AMP MotorCarrying Handle Miter Lock HandleSpindle Lock Button Trigger LockPositive Stops on Miter Table Bevel Lock KnobElectric Brake Miter FenceAssembly Dust GuideDust BAG Work ClampTable Extensions Stop BlockClamp Bracket Bracket Screw Small Stop Block Wing Screw Extension Miter SAW BaseTo Install Blade Squaring the Miter Table to the Fence See Figures 17Framing Square Miter Fence Miter Table Miter Lock Handle View of Miter Table Square with FenceAdjustments Miter Fence Miter TableSquaring the SAW Blade to the Fence See Figures 21Miter Fence Blade Miter Framing Table SquareSquaring the Blade to the Miter Table See Figures 25Blade Combination Miter SquarePivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentCutting a Slot in the Zero Clearance Throat Plate Depth StopOperation Cutting with Your Compound Miter SAWCrosscutting To Crosscut with Your Miter SAWBevel CUT Indicator Point Bevel CUTSee Figures 30 Mounting BracketTo Make a Compound CUT with Your Miter SAW Compound Miter CUTCompound Miter CUT Support Long Workpieces Jamming the blade. See Figures 36Long Workpiece Workpiece SupportsCOMPOUND-ANGLE Settings for Popular Structures Cutting Compound MitersCutting Crown Molding Laying Molding Flat on the Miter TableCutting Warped Material Clamping Wide WorkpiecesRight WrongMaintenance GeneralLubrication Extension CordsOperators Manual Ryobi TECHNOLOGIES, INC
Top Page Image Contents