Ryobi TS1350 warranty Squaring the SAW Blade to the Fence, See Figures 21, Miter Fence

Page 17

ADJUSTMENTS

SQUARING THE SAW BLADE TO THE FENCE

See Figures 21 - 24

■Unplug your saw.

WARNING:

Failure to unplug your saw could result in accidental starting causing possible serious personal injury.

■Pull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position.

■Loosen the miter lock handle approximately one-half turn.

■Depress the miter lock plate and rotate the miter table until the pointer on the control arm is positioned at 0° .

■Release the miter lock plate and securely tighten the miter lock handle.

■Lay a framing square flat on the miter table. Place one leg of the square against the fence. Slide the other leg of the square against the flat part of saw blade.

Note: Make sure that the square contacts the flat part of the saw blade, not the blade teeth.

■The edge of the square and the saw blade should be parallel as shown in figure 21.

■If the front or back edge of the saw blade angles away from the square as shown in figures 22 and 23, adjust- ments are needed.

■Loosen the socket head screws that secure the mount- ing bracket to the miter table. See Figure 24.

■Rotate the mounting bracket left or right until the saw blade is parallel with the square.

MITER

FENCE

45

30

2.5 2

15

45

30

 

0

31.62

22.5

15

BLADE

MITER FRAMING

TABLE SQUARE

VIEW OF BLADE NOT SQUARE WITH

 

FENCE, ADJUSTMENTS ARE REQUIRED

Fig. 22

 

MITER

FENCE

4

5

30

2.5 2

15

45

30

 

0

31.62

22.5

15

BLADE

MITER FRAMING

TABLE SQUARE

■Retighten the screws securely and recheck the blade- to-fence alignment.

MITER

FENCE

VIEW OF BLADE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED

Fig. 23

SOCKET

HEAD SCREWS

45

30

.5 22

15

45

30

 

0

31.62

22.5

15

BLADE

MITER

LOCK

FRAMINGPLATE

MITER SQUARE

TABLE

MITER

LOCK HANDLE

VIEW OF BLADE

SQUARE WITH FENCE

Fig. 21

Page 17

5 1

31.62

30

22.5

 

MOUNTING

BRACKET

MITER

TABLE

Fig. 24

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Thank YOU for Buying a Ryobi Compound Miter SAW Save this Manual for Future ReferenceIntroduction Table of ContentsProduct Specifications Double Insulation Symbol MeaningRules for Safe Operation Read ALL Instructions Before Making a CUT, be sure all adjustments are secure Freehand Glossary of Terms for WoodworkingTools Needed UnpackingCombination Square Framing SquareDust BAG Loose Parts ListWork Clamp Miter Lock Handle Stop BlockKnow Your Compound Miter SAW FeaturesCutting Capacities AMP MotorMiter Lock Handle Carrying HandleSpindle Lock Button Trigger LockBevel Lock Knob Positive Stops on Miter TableElectric Brake Miter FenceDust Guide AssemblyDust BAG Work ClampStop Block Table ExtensionsClamp Bracket Bracket Screw Small Stop Block Wing Screw Extension Miter SAW BaseTo Install Blade See Figures 17 Squaring the Miter Table to the FenceFraming Square Miter Fence Miter Table Miter Lock Handle View of Miter Table Square with FenceMiter Fence Miter Table AdjustmentsSee Figures 21 Squaring the SAW Blade to the FenceMiter Fence Blade Miter Framing Table SquareSee Figures 25 Squaring the Blade to the Miter TableBlade Combination Miter SquareBevel Pivot Adjustment Pivot Adjustments Travel Pivot AdjustmentCutting a Slot in the Zero Clearance Throat Plate Depth StopCutting with Your Compound Miter SAW OperationCrosscutting To Crosscut with Your Miter SAWBevel CUT Bevel CUT Indicator PointSee Figures 30 Mounting BracketCompound Miter CUT Compound Miter CUTTo Make a Compound CUT with Your Miter SAW Jamming the blade. See Figures 36 Support Long WorkpiecesLong Workpiece Workpiece SupportsCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresLaying Molding Flat on the Miter Table Cutting Crown MoldingClamping Wide Workpieces Cutting Warped MaterialRight WrongGeneral MaintenanceLubrication Extension CordsRyobi TECHNOLOGIES, INC Operators Manual
Top Page Image Contents