Ryobi TS1351 manual Operation, Pivot Adjustments Travel Pivot Adjustment, Bevel Pivot Adjustment

Page 19

ADJUSTMENTS

POSITIVE STOP

ADJUSTMENT

SCREW FOR

0° ANGLES

POSITIVE STOP

ADJUSTMENT

LOCK NUT(S)SCREW FOR 45° ANGLES

Fig. 28

PIVOT ADJUSTMENTS

Note: These adjustments were made at the factory and normally do not require readjustment.

TRAVEL PIVOT ADJUSTMENT

■The saw arm should rise completely to the up position by itself.

■If the saw arm does not raise by itself or if there is play in the pivot joints, have saw repaired by at your nearest

RYOBI AUTHORIZED SERVICE CENTER.

BEVEL PIVOT ADJUSTMENT

■Your compound miter saw should bevel easily by loos- ening the bevel lock knob and tilting the saw arm to the left.

■If movement is tight or if there is play in the pivot, have saw repaired by at your nearest RYOBI AUTHORIZED

SERVICE CENTER.

WARNING:

Do not start your compound miter saw without checking for interference between the blade and the miter table support. Damage could result to the blade if it strikes the miter table support during operation of the saw.

APPLICATIONS

(Use only for the purposes listed below)

■Cross cutting wood and plastic.

■Cross cutting miters, joints, etc. for picture frames, moldings, door casings, and fine joinery.

Note: The blade provided is fine for most wood cutting operations, but for fine joinery cuts or cutting plastic, use one of the accessory blades available from your Ryobi dealer.

OPERATION

WARNING:

Before starting any cutting operation, clamp or bolt your miter saw to a workbench. Never operate your miter saw on the floor or in a crouched position. Failure to heed this warning can result in serious personal injury.

WARNING:

To avoid serious personal injury, keep your hands outside the no hands zone; at least 3 in. (7.6 cm) from blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.

CUTTING A SLOT IN THE ZERO CLEARANCE THROAT PLATE

In order to use your compound miter saw, you must cut a slot through the zero clearance throat plate to allow for blade clearance. To cut the slot, set your saw at 0° miter, turn saw on and allow the blade to reach full speed, then carefully make a straight cut as far as it will go through the throat plate. Turn your saw off and allow the blade to come to a complete stop before raising the saw arm.

Next, adjust the bevel angle to 45°, turn your saw on and allow the blade to reach full speed, then carefully make another cut through the zero clearance throat plate. The slot in the throat plate will then be wide enough to allow the blade to pass through it at any angle from 0° to 45°.

Page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsIntroduction Double Insulation Symbol MeaningSafety and International Symbols Rules for Safe OperationRead ALL Instructions Blade Coasts After Being Turned OFF Freehand Glossary of Terms for WoodworkingTools Needed UnpackingLoose Parts List Cutting Capacities FeaturesKnow Your Compound Miter SAW AMP MotorSpindle Lock Button Blade Wrench / Storage AreaCarrying Handle Miter Lock HandleMounting Holes Positive Stops on Miter TableBevel Lock Knob Electric BrakeWork Clamp AssemblyDust Guide Dust BAGSee Figures 11 Table ExtensionsStop Block See Figures 11, 12,See Figures 15 To Install BladeSee Figures 17 Squaring the Miter Table to the FenceSquaring the SAW Blade to the Fence AdjustmentsSee Figures 20 Miter Fence See Figures 25 Squaring the Blade to the Miter TableApplications Pivot Adjustments Travel Pivot AdjustmentBevel Pivot Adjustment OperationCrosscutting Cutting with Your Compound Miter SAWTo Crosscut with Your Miter SAW See Figures 30 Bevel CUTTo Make a Compound CUT with Your Miter SAW Compound Miter CUTSupport Long Workpieces Cutting Compound Miters Laying Molding Flat on the Miter Table Cutting Crown MoldingClamping Wide Workpieces Cutting Warped MaterialSee Figures 36 Extension Cords MaintenanceGeneral LubricationRyobi TECHNOLOGIES, INC Mm Compound Miter Saw

TS1351 specifications

The Ryobi TS1351 is a versatile and robust table saw designed to meet the needs of both DIY enthusiasts and professional woodworkers. Known for its impressive performance and user-friendly features, the TS1351 stands out in its category, making it an ideal choice for those looking to enhance their woodworking capabilities.

One of the key features of the Ryobi TS1351 is its powerful 15 Amp motor, which delivers ample cutting power for a variety of tasks. This motor enables users to cut through hardwoods, softwoods, and even engineered materials with ease. The saw offers a maximum cutting depth of 3-1/8 inches at 90 degrees, allowing for substantial cuts in thicker materials.

The TS1351 is equipped with a 10-inch carbide-tipped blade that provides a fine finish and extended blade life. The blade can be adjusted for height and angle, allowing for precise bevel cuts of up to 45 degrees. This versatility makes it possible to perform a wide range of cuts, including crosscuts, rip cuts, and miter cuts, making the saw suitable for diverse woodworking projects.

Safety is a priority with the Ryobi TS1351. It features a blade guard and an anti-kickback pawl, which help protect users during operation. The push stick, included with the saw, further enhances safety by allowing operators to make cuts without putting their hands near the blade. Additionally, the sturdy base offers stability, reducing vibrations and ensuring accurate cuts.

Another innovative characteristic of the TS1351 is its portability. Weighing in at just over 50 pounds, the saw is easy to transport, making it suitable for job sites or home workshops. The onboard storage for accessories also helps keep the workspace organized and reduces setup time.

The Ryobi TS1351 further enhances user experience with its quick-release guard, easy-to-read scales, and a large table surface that provides ample room for material support. Whether tackling small projects or larger builds, this table saw delivers reliable performance, precision, and safety, making it a valuable tool for any woodworker or craftsperson.
Top Page Image Contents