Ryobi TS1351 Cutting with Your Compound Miter SAW, Crosscutting, To Crosscut with Your Miter SAW

Page 20

OPERATION

CUTTING WITH YOUR COMPOUND MITER SAW

WARNING:

When using a work clamp or C-clamp to secure your workpiece, clamp workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece. The workpiece binding the blade will cause motor stalling and kickback. This situation could cause an accident resulting in possible serious personal injury.

CROSSCUTTING

See Figure 29.

A crosscut is made by cutting across the grain of the workpiece. A straight crosscut is made with the miter table set at the 0° position. Miter crosscuts are made with the miter table set at some angle other than zero.

TO CROSSCUT WITH YOUR MITER SAW

■Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board is placed against the fence, the board could collapse on the blade at the end of the cut, jamming the blade. See Figures 36 and 37.

■When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table. See Figure 34.

■Align cutting line on the workpiece with the edge of saw blade.

■Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible. See Figure 29.

■Pull out the lock pin and lift saw arm to its full height.

■Loosen the miter lock handle. Rotate the miter lock handle approximately one-half turn to the left to loosen.

■Press the miter lock plate down with your thumb and hold.

■Rotate the control arm until the pointer aligns with the desired angle on the miter scale.

■Release the miter lock plate.

Note: You can quickly locate 0°, 22-1/2°left or right, and 45° left or right by releasing the lock plate as you rotate the control arm. The lock plate will seat itself in one of the positive stop notches, located in the miter table frame.

■Tighten the miter lock handle securely.

WARNING:

To avoid serious personal injury, always tighten the miter lock handle securely before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut.

45

30

15

STRAIGHT

CROSSCUT

 

45

1

30

.5

5 1

 

31.62

30

22.5

45

 

 

 

WORK CLAMP

Fig. 29

Page 20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Operators Manual Save this Manual for Future ReferenceIntroduction Table of ContentsProduct Specifications Symbol Meaning Safety and International SymbolsRules for Safe Operation Double InsulationRead ALL Instructions Blade Coasts After Being Turned OFF Glossary of Terms for Woodworking FreehandUnpacking Tools NeededLoose Parts List Features Know Your Compound Miter SAWAMP Motor Cutting CapacitiesBlade Wrench / Storage Area Carrying HandleMiter Lock Handle Spindle Lock ButtonPositive Stops on Miter Table Bevel Lock KnobElectric Brake Mounting HolesAssembly Dust GuideDust BAG Work ClampTable Extensions Stop BlockSee Figures 11, 12, See Figures 11To Install Blade See Figures 15Squaring the Miter Table to the Fence See Figures 17See Figures 20 AdjustmentsSquaring the SAW Blade to the Fence Miter Fence Squaring the Blade to the Miter Table See Figures 25Pivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentOperation ApplicationsTo Crosscut with Your Miter SAW Cutting with Your Compound Miter SAWCrosscutting Bevel CUT See Figures 30Compound Miter CUT To Make a Compound CUT with Your Miter SAWSupport Long Workpieces Cutting Compound Miters Cutting Crown Molding Laying Molding Flat on the Miter TableSee Figures 36 Cutting Warped MaterialClamping Wide Workpieces Maintenance GeneralLubrication Extension CordsMm Compound Miter Saw Ryobi TECHNOLOGIES, INC

TS1351 specifications

The Ryobi TS1351 is a versatile and robust table saw designed to meet the needs of both DIY enthusiasts and professional woodworkers. Known for its impressive performance and user-friendly features, the TS1351 stands out in its category, making it an ideal choice for those looking to enhance their woodworking capabilities.

One of the key features of the Ryobi TS1351 is its powerful 15 Amp motor, which delivers ample cutting power for a variety of tasks. This motor enables users to cut through hardwoods, softwoods, and even engineered materials with ease. The saw offers a maximum cutting depth of 3-1/8 inches at 90 degrees, allowing for substantial cuts in thicker materials.

The TS1351 is equipped with a 10-inch carbide-tipped blade that provides a fine finish and extended blade life. The blade can be adjusted for height and angle, allowing for precise bevel cuts of up to 45 degrees. This versatility makes it possible to perform a wide range of cuts, including crosscuts, rip cuts, and miter cuts, making the saw suitable for diverse woodworking projects.

Safety is a priority with the Ryobi TS1351. It features a blade guard and an anti-kickback pawl, which help protect users during operation. The push stick, included with the saw, further enhances safety by allowing operators to make cuts without putting their hands near the blade. Additionally, the sturdy base offers stability, reducing vibrations and ensuring accurate cuts.

Another innovative characteristic of the TS1351 is its portability. Weighing in at just over 50 pounds, the saw is easy to transport, making it suitable for job sites or home workshops. The onboard storage for accessories also helps keep the workspace organized and reduces setup time.

The Ryobi TS1351 further enhances user experience with its quick-release guard, easy-to-read scales, and a large table surface that provides ample room for material support. Whether tackling small projects or larger builds, this table saw delivers reliable performance, precision, and safety, making it a valuable tool for any woodworker or craftsperson.
Top Page Image Contents