Grizzly G1095/G1096 Changing Speeds, To change the feed rate of your power feeder, Motor OFF

Page 23

Changing Speeds

Always disconnect power to the machine before performing installation or maintenance. Failure to do this may result in serious personal injury.

Your power feeder has the option to feed a workpiece at 13, 26, 33, and 66 feet per minute.

These rates are achieved by changing the combi- nation of change gears, and by turning the motor switch to high or low range operation.

To change the feed rate of your power feeder:

1.DISCONNECT THE POWER FEEDER FROM POWER!

2.Make sure the speed dial is pointing to "0" (the OFF position, Figure 13).

Figure 13. Feed direction and speed dial.

Model G1095/G1096 1-HP Power Feeder

3.Refer to the feed rate list below to find the gear combination required for your chosen feed rate.

13 Ft Per Min: A, 25 Tooth + B,

40 Tooth.

26 Ft Per Min: A, 40 Tooth + B, 25

Tooth.

33 Ft Per Min: A, 25 Tooth + B, 40

Tooth.

66 Ft Per Min: A, 40 Tooth + B, 25

Tooth.

Motor OFF.

4.Remove the chain cover and the two hex nuts securing the A & B change gears to the shafts shown in Figure 14.

Change Gear

Position A

Change Gear Position B

Figure 14. Change gear locations.

5.Swap the required change gears so the gear hubs are facing in toward the power feeder (shown in positions A & B in Figure 14).

6.Reinstall the hex nuts and chain cover.

7.Connect the power feeder to power and move the feed direction and speed dial to the high or low range.

-21-

Image 23

Contents HP Power Feeder Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Machine Data Sheet Other Model G1096 Power Feeder 4 Roller / 4 Speed Phase Model G1095/G1096 1-HP Power Feeder Identification Controls and features Model G1095/G1096 1-HP Power Feeder !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29# 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2Additional Safety for Power Feeders Circuit Requirements 220V Single-Phase Operation G1095Nema 15-15 plug and receptacle 220V Three-Phase Operation G1096Unpacking SetupSetup Safety Items Needed for SetupBox Inventory Figures 4 Qty InventoryHardware Recognition Chart Assembled power feeder Model G1095/G1096 1-HP Power Feeder Clean Up AssemblyShaper Jointer Tablesaw Base MountingThrough-Bolt Mounting Test Run To test run the power feederOperations Operation Safety Basic Use and CareFt Per Min A, 40 Tooth + B To change the feed rate of your power feederChanging Speeds Ft Per Min A, 25 Tooth + BLubrication MaintenanceCleaning ScheduleTroubleshooting ServiceWheel Replacement Electrical Safety Instructions WiringElectrical IgZZEVhZ Feeder PartsDescription Stand and Support Assembly 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%