Hobart Welding Products 700I, HP-70 manual Installing Alternative Plug, Cable Management Strap

Page 21

.A complete Parts List is available at www.MillerWelds.com

4-13. Installing Alternative Plug

. This procedure is necessary if the unit is to be connected to a 208/230 VAC receptacle that requires a plug that is different from the supplied plug.

1Supplied 230 VAC Plug Cut cord close to plug.

2 Alternative Plug (230 VAC

Plug Shown)

3Input (Black Lead) (Brass) Terminal

4Input (White Lead) (Brass) Terminal

5 Ground (Green) Terminal

Tools Needed:

6	Outer Shell
7	Cord Grip

Strip cord jacket back enough to separate conductors.

Strip conductors enough to make good contact with plug terminals. Make plug connections and reinstall outer shell and cord grip. Tighten assembly screws onto shell. Do not overtighten.

Ref. 801 305-A / 801 611

4-14. Cable Management Strap

1 Cable Management Strap

Coil cables together and secure to unit using the cable management strap.

244 413-A / 244 412-A

OM-244 013 Page 17

Image 21

Contents Processes OM-244 013CDescription File Plasma CuttersFrom Miller to You Table of Contents Page Plasma Arc Cutting Hazards Symbol UsageCutting can cause fire or explosion Electric Shock can killARC Rays can burn eyes and skin Flying Sparks can injureNoise can damage hearing Fumes and Gases can be hazardousMoving Parts can injure HOT Parts can burnFlying Metal or Dirt can injure eyes Overuse can cause OverheatingCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesConsignes DE Sécurité Lire Avant Utilisation Signification des symbolesLE Coupage présente un risque de feu ou d’explosion UN Choc Électrique peut tuerLES Étincelles Projetées peuvent provoquer des blessures Risque de blessure en casLE Bruit peut endommager l’ouïe LES Fumées ET LES GAZ peuvent être dangereuxLES Bouteilles peuvent exploser si elles sont endommagées ’ARC Plasma peut provoquer des blessuresLES Pièces Chaudes peuvent provoquer des brûlures Les Pièces Mobiles peuvent provoquer des blessuresLA Chute DE L’ÉQUIPEMENT peut provoquer des blessures ’EMPLOI Excessif peutRisque D’INCENDIE OU LE Coupage Ã L’ARC peut causer des interférencePrincipales normes de sécurité Proposition californienne 65 AvertissementsInformations relatives aux CEM En ce qui concerne les implants médicauxDefinitions I1maxI1eff Specifications InstallationTorch Dimensions And Weight Power Source Dimensions And WeightDimensions And Weight Duty Cycle And OverheatingConnecting Work Clamp Connecting Gas/Air SupplyDo not move or operate unit where it could tip Selecting a LocationExtension Cord Data Electrical Service GuideSerial Number And Rating Label Location Connecting 1-Phase Input Power For 240 VACProng Not Used Engine Control Switch must be set at RUNAlways connect green or Terminal, never to a loadCable Management Strap Installing Alternative PlugElectrode Wrench Controls OperationMild Steel Recommended Cut Speed Trigger Safety LockPlasma Cutting System Practices Pilot arc starts immediately when trigger is pressedExample Of Cutting Operation Sequence Of Cutting OperationExample Of Cutting Using Stand-off Guide Sequence Of Cutting Using Stand-off GuideSequence Of Piercing Operation Routine Maintenance Maintenance & TroubleshootingDisconnect power Before maintainingChecking Or Replacing Filter Element Checking Shield Cup Shutdown System Status/Trouble LightsTurn Off power source before checking torch parts Checking/Replacing Retaining Cup, Tip, And ElectrodeElectrode Wrench Torch And Work Cable Connections Torch ConnectionsWork Cable Connections Trouble Remedy Troubleshooting Power SourceArc goes on and off while cutting Troubleshooting TorchCircuit Diagram Electrical Diagram244 011-B Parts List Recommended Spare PartsRecommended Spare Parts Support ServiceMiller Electric Mfg. Co Owner’s Record