Hobart Welding Products OM-947 manual Fire or Explosion hazard, Falling Equipment can injure

Page 7

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.

FALLING EQUIPMENT can injure.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

DKeep equipment (cables and cords) away from moving vehicles when working from an aerial location.

DFollow the guidelines in the Applications Manual for the Revised NIOSH Lifting Equation (Publication No. 94−110) when manu- ally lifting heavy parts or equipment.

MOVING PARTS can injure.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards closed and securely in place.

DHave only qualified persons remove doors, panels, covers, or guards for maintenance and troubleshooting as necessary.

DReinstall doors, panels, covers, or guards when maintenance is finished and before reconnecting input power.

READ INSTRUCTIONS.

DRead and follow all labels and the Owner’s Manual carefully before installing, operating, or servicing unit. Read the safety information at the beginning of the manual and in each section.

DUse only genuine replacement parts from the manufacturer.

DPerform maintenance and service according to the Owner’s Manuals, industry standards, and national, state, and local codes.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

FLYING SPARKS can injure.

D Wear a face shield to protect eyes and face.

D Shape tungsten electrode only on grinder with proper guards in a safe location wearing proper face, hand, and body protection.

DSparks can cause fires — keep flammables away.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can injure.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can injure.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

OM-947 Page 3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Description ProcessesFile Flux Cored Fcaw Protect Your Investment From Hobart to YouTable of Contents Warranty HOT Parts can burn Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can injure Welding Wire can injureFire or Explosion hazard Falling Equipment can injureAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLES Fumées ET LES GAZ peuvent être dangereux LES Pièces Chaudes peuvent provoquer des brûluresLE Soudage peut provoquer un incendie ou une explosion LA Chute DE L’ÉQUIPEMENT peut provoquer des blessures LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OULE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLes Pièces Mobiles peuvent causer des blessures LES Fils DE Soudage peuvent provoquer des blessuresInformations relatives aux CEM Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-947 − Definitions − SpecificationsSymbols And Definitions SpecificationsVolt-Ampere Curves Duty Cycle And OverheatingInstalling Work Clamp − InstallationTools Needed Slide insulating grips over handles OM-947 Changing Polarity Process/Polarity TableTools Needed 11/16, 1-1/8 Shielding Gas Installing Gas SupplyTools Needed Installing Wire Spool And Adjusting Hub Tension460 mm Serial Number And Rating Label LocationTurn off welding power source Installing Contact Tip And NozzleThreading Welding Wire Load − OperationControls Operating The GunOM-947 Weld Parameter Chart 210 Drive Motor Protection − Maintenance &TROUBLESHOOTINGRoutine Maintenance Overload ProtectionChanging Drive Roll Or Wire Inlet Guide Replacing Gun Contact Tip Turn Off power before replacing contact tipCleaning Gun Liner Head Mm / 10 mm Tube Replacing Gun LinerLoosen liner setscrew 10 mm Trouble Remedy Troubleshooting TableSecure power cord plug in receptacle see Section Power source see SectionCircuit Diagram − Electrical DiagramTypical Fcaw Process Connections − Wire Welding GuidelinesTypical MIG Process Connections Select Voltage Typical Control SettingsWire Size Amperage Range AmperageGroove Welds Holding And Positioning Welding GunShort Normal Long Conditions That Affect Weld Bead ShapeSlow Normal Fast Good Weld Bead Characteristics Poor Weld Bead CharacteristicsGun Movement During Welding Possible Causes Corrective Actions Troubleshooting − Excessive SpatterTroubleshooting − Porosity Troubleshooting − Excessive PenetrationTroubleshooting − Incomplete Fusion Troubleshooting − Lack Of PenetrationTroubleshooting − Burn-Through Troubleshooting − Distortion Troubleshooting − Waviness Of BeadTroubleshooting Guide For Semiautomatic Welding Equipment Main Assembly − Parts ListOptional Pkg 195 157R− See Table Pkg209 195 Hub Kit For 8 in Wire SpoolWeatherproof Nylon Work like a Pro Page Page Support ServiceAssistance Hobart Welding Products Contact your Distributor for

OM-947 specifications

Hobart Welding Products has made a significant mark in the welding industry with its cutting-edge equipment, and the Hobart OM-947 is no exception. This multi-process welder stands out for its versatility and user-friendly design, ideal for both beginners and experienced welders alike.

One of the main features of the OM-947 is its multi-process capability, allowing users to perform MIG, TIG, and stick welding, all in one machine. This flexibility makes it an appealing choice for diverse welding applications, whether in automotive repair, metal fabrication, or industrial maintenance. The OM-947 can easily switch between processes, ensuring efficiency and convenience in various tasks.

The machine is engineered with advanced technology that enhances welding performance. Its inverter technology provides a stable arc and reduces energy consumption, which not only cuts down operational costs but also improves the welder's overall performance. The Hobart OM-947 boasts a high-duty cycle, allowing users to operate it for extended periods without overheating, making it suitable for professional environments.

In terms of characteristics, the OM-947 features a digital display that allows for precise control over welding parameters. This user-friendly interface simplifies the adjustment process, enabling welders to focus more on their craft rather than struggling with complex settings. The machine also comes with a built-in automatic voltage control, which adjusts the voltage according to the chosen process and material thickness, ensuring optimal welding conditions and reducing the risk of defects.

Another notable aspect of the OM-947 is its portability. Weighing in at a manageable level, coupled with a compact design, the machine is easy to transport between job sites, making it ideal for mobile welders. Furthermore, the rugged construction of the unit ensures durability even in demanding environments.

Safety features are paramount in welding equipment, and the Hobart OM-947 does not disappoint. It includes a thermal overload protection system that prevents overheating and potential damage to the welder, offering peace of mind during use.

Overall, the Hobart Welding Products OM-947 delivers impressive performance, versatility, and user-friendliness. It is designed for welders who demand quality and reliability from their equipment while being accessible enough for those who are just starting their welding journey. With its innovative features and robust design, the OM-947 truly sets a benchmark in the world of welding.
Top Page Image Contents