Stow SFCS-16 manual Operation, Transporting the Floor Covering Scraper

Page 19

ASSEMBLY INSTRUCTIONS/OPERATION

DAMAGE AND/OR PERSONAL INJURY. BLADES ARE PROVIDED WITH A PROTECTIVE COVER OVER THE CUTTING EDGE. EXERCISE EXTREME

CAUTION WHEN REMOVING AND/OR REINSTALLING THE PROTECTIVE COVER. STORE THE BLADE WITH THE PROTECTIVE COVER PROPERLY INSTALLED TO MINIMIZE THE POTENTIAL FOR BLADE DAMAGE AND/OR PERSONAL INJURY.

7)Return the FLOOR COVERING SCRAPER to its normal operating position.

8)Determine that the ON/OFF switch located on the operator handle is in the OFF position. IF the FLOOR COVERING SCRAPER is to be used immediately, then reconnect the extension cord or FLOOR COVERING SCRAPER to the power source.

DANGER

UNEXPECTED MACHINE START UP CAN RESULT IN PROPERTY DAMAGE AND/OR PERSONAL INJURY.

Operation

OPERATIONAL DISCLAIMER.

THE MANUFACTURER OF THE FLOOR COVERING SCRAPER MAKES NO WARRANTY OR GUARANTEE THAT IT IS MERCHANTABLE AND/OR SUITABLE FOR ANY SPECIFIC JOB APPLICATION AND THAT IT WILL HAVE THE CAPABILITY AND POWER REQUIRED TO REMOVE ANY SPECIFIC COVERING FROM ANY SPECIFIC WORK SURFACE.

CALIFORNIA PROPOSITION 65 DISCLAIMER.

DANGER

THE DUSTS/BYPRODUCTS FROM THE COVERING REMOVAL PROCESS ASSOCIATED WITH THE OPERATION OF THE FLOOR COVERING SCRAPER CAN CONTAIN CHEMICALS KNOWN TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER REPRODUCTIVE HARM.

INFORMATION RELATIVE TO MINIMUM COMPONENT STANDARDS FOR THE OPERATION OF THE FLOOR COVERING SCRAPER.

For operational safety and overall productivity considerations, it is required that specific FLOOR COVERING SCRAPER components meet minimum acceptable operational standards BEFORE utilization:

1)Operator handle be properly mounted to the main frame, with factory supplied ball-detent type retaining pins that properly secure the handle to the main frame while in the work position.

2)The operator handle is equipped with properly fitting handle grips of sufficient integrity to allow for proper job function as outlined within this manual. Loose fitting handle grips or grips without full end caps are not permitted.

3)An ON/OFF motor switch that allows it to perform its intended job function as outlined within this manual. Replace any damaged ON/OFF motor switch with a factory approved replacement part only.

4)An extension cord and GFI that allows this accessory to perform its intended job function as outlined within this manual. Replace any damaged extension cord or GFI with a factory approved replacement part only.

5)Exciter plate elastomeric rubber mounts which allow them to perform their intended job function as outlined within this manual. Do not operate the FLOOR COVERING SCRAPER without the correct number of exciter plate elastomeric rubber mounts. Do not operate the FLOOR COVERING SCRAPER with a damaged and/or improperly secured rubber mount. Replace any damaged rubber mount with a factory approved replacement part only.

6)Blade(s) and/or ceramic tile ripper attachment of proper structural integrity (void of cracks, etc), straightness, sharpness, etc which are retained by the proper fasteners. Replace worn or damaged blades, fasteners and the ceramic tile ripper attachment with a factory approved replacement part only.

7)All safety decals, Operator Manual and operational information decals (including the applicable Quik Tips information) must be in proper and readable condition. Replace any missing or damaged safety decal, Operator Manual and/or information decal with a factory approved replacement part only.

TRANSPORTING THE FLOOR COVERING SCRAPER.

The FLOOR COVERING SCRAPER has an operational weight that prohibits one person from loading and/or unloading it alone by conventional, physical efforts.

SFCS-16

OPERATION AND PARTS MANUAL REV #3 (02/23/06)

PAGE 19

 

 

 

Image 19
Contents Floor Covering Scraper Model SFCS-16 Page Stow SFCS-16 Floor Covering Scrapper Stow Construction Equipment Here’s how to get helpSFCS-16 Operation and Parts Manual REV #3 02/23/06 SFCS-16 Operation and Parts Manual REV #3 02/23/06 Operator Instructional Data Sheet Safety Precautions Operation MAINTENANCE, Repair and Storage Removing the Floor Covering Scraper from the Pallet AssemblyTheory of Operation Before Starting the MotorAngled Mastic Removal Blade Straight Beveled Scoring Blades Result in Property Damage AND/OR Personal Injury Assembly INSTRUCTIONS/OPERATION Assembly INSTRUCTIONS/OPERATION Assembly INSTRUCTIONS/OPERATION Transporting the Floor Covering Scraper OperationFloor Covering SCRAPER. Figure Adjusting the Operator Handle Height Assembly INSTRUCTIONS/OPERATION Assembly INSTRUCTIONS/OPERATION Assembly INSTRUCTIONS/OPERATION Assembly INSTRUCTIONS/OPERATION Assembly INSTRUCTIONS/OPERATION Stopping the Floor Covering Scraper on the Jobsite Assembly INSTRUCTIONS/OPERATION Preventative Maintenance Check List ServiceAssembly INSTRUCTIONS/OPERATION Electric Motor Service Requirements TroubleshootingOperational Problems Electric MotorStorage StorageFrame SpecificationsGeneral SFCS-16 Operation and Parts Manual REV #3 02/23/06 Explanation of Code in Remarks Column Recommended Spare Parts Adjustable Axle Assy Remarks Part Name QTYReplacement Cutting Blades Assy Part Name Frame Assy Part Name QTY Remarks Frame Assy SFCSSP80430 BEARING, Flange Operator Handle Assy HANDLE, Lower Decals Decals Part Name QTY Freight Policy Special Expediting ServicePRICING, Rebates Specifications Payment TermsSFCS-16 Operation and Parts Manual REV #3 02/23/06 FAX Heres HOW to GET Help