Stow SFCS-16 manual Floor Covering SCRAPER. Figure

Page 20

ASSEMBLY INSTRUCTIONS/OPERATION

DANGER

DO NOT ATTEMPT TO LIFT THE FLOOR

COVERING SCRAPER UP INTO A TRANSPORTATION VEHICLE WITH THE USE OF ONE PERSON ALONE. DO NOT ATTEMPT TO LOWER THE FLOOR COVERING SCRAPER FROM A TRANSPORTATION VEHICLE WITH THE USE OF ONE PERSON ALONE. LIFT AND/OR LOWER THE FLOOR COVERING SCRAPER ONLY BY THE USE OF A POWER TAILGATE UNIT, A SUITABLE HOIST UNIT OF PROPER CAPACITY AND/OR CONFIGURATION OR BY THE USE OF A PROPER QUANTITY OF PERSONNEL IN PROPER PHYSICAL/MENTAL CONDITION.

1)The FLOOR COVERING SCRAPER can be hoisted by a mechanical device incorporating a chain and suitable attachment device to the lifting bail area located behind the electric motor. FIGURE 18. This location may not always locate the exact position of the center of gravity for the FLOOR COVERING SCRAPER. Lifting handles are also provided on both sides of the main frame. These handles can be utilized by personnel whenever lifting/lowering the

FLOOR COVERING SCRAPER. FIGURE 19.

FIGURE 18

DANGER

EXERCISE EXTREME CAUTION WHEN UTILIZING A MECHANICAL DEVICE FOR LIFTING THE FLOOR COVERING SCRAPER. UTILIZE THE MECHANICAL DEVICE IN ACCORDANCE TO BOTH ITS DESIGNED STATIC AND DYNAMIC LOADING ENVELOPES. DO NOT UTILIZE THE MECHANICAL DEVICE UNTIL THIS INFORMATION IS PROPERLY KNOWN AND UNDERSTOOD BY ALL APPLICABLE PERSONNEL. FAILURE TO PROPERLY UTILIZE THE MECHANICAL DEVICE

CAN RESULT IN PROPERTY DAMAGE AND/OR PERSONAL INJURY.

CAUTION

Do not drop the FLOOR COVERING SCRAPER directly upon the exciter plate. Direct impact against the exciter plate can result in damage to components including the plate, elastomeric rubber mounts, electric motor shaft, bearings, etc.

FIGURE 19

2)To minimize the possibility of damage to the FLOOR COVERING SCRAPER, always transport in its normal, upright position. All equipment must be secured in/on vehicles with suitable strapping or tie- downs. Personnel should not be transported in the same compartment as equipment. Consult applicable OSHA and transportation regulations (local, State and Federal) for the proper transportation of the FLOOR COVERING SCRAPER.

3)Do not transport the FLOOR COVERING SCRAPER with a blade or the ceramic tile ripper attachment attached to the main frame in the following configurations:

a) To and from the jobsite.

b) For longer distances while being repositioned on the jobsite.

c)When traversing up and down stairways.

d)While performing maintenance and/or repairs.

e)Lifting up/into or/down from a transporting vehicle. Remove the blade or ceramic tile ripper attachment according to the procedures as outlined in this manual for the above listed configurations.

SFCS-16

OPERATION AND PARTS MANUAL REV #3 (02/23/06)

PAGE 20

 

 

 

Image 20
Contents Floor Covering Scraper Model SFCS-16 Page Stow SFCS-16 Floor Covering Scrapper Here’s how to get help Stow Construction EquipmentSFCS-16 Operation and Parts Manual REV #3 02/23/06 SFCS-16 Operation and Parts Manual REV #3 02/23/06 Operator Instructional Data Sheet Safety Precautions Operation MAINTENANCE, Repair and Storage Assembly Removing the Floor Covering Scraper from the PalletBefore Starting the Motor Theory of OperationAngled Mastic Removal Blade Straight Beveled Scoring Blades Result in Property Damage AND/OR Personal Injury Assembly INSTRUCTIONS/OPERATION Assembly INSTRUCTIONS/OPERATION Assembly INSTRUCTIONS/OPERATION Operation Transporting the Floor Covering ScraperFloor Covering SCRAPER. Figure Adjusting the Operator Handle Height Assembly INSTRUCTIONS/OPERATION Assembly INSTRUCTIONS/OPERATION Assembly INSTRUCTIONS/OPERATION Assembly INSTRUCTIONS/OPERATION Assembly INSTRUCTIONS/OPERATION Stopping the Floor Covering Scraper on the Jobsite Assembly INSTRUCTIONS/OPERATION Service Preventative Maintenance Check ListAssembly INSTRUCTIONS/OPERATION Electric Motor Service Troubleshooting Operational ProblemsElectric Motor RequirementsStorage StorageGeneral SpecificationsFrame SFCS-16 Operation and Parts Manual REV #3 02/23/06 Explanation of Code in Remarks Column Recommended Spare Parts Adjustable Axle Assy Part Name QTY RemarksReplacement Cutting Blades Assy Part Name Frame Assy Part Name QTY Remarks Frame Assy SFCSSP80430 BEARING, Flange Operator Handle Assy HANDLE, Lower Decals Decals Part Name QTY Special Expediting Service PRICING, Rebates SpecificationsPayment Terms Freight PolicySFCS-16 Operation and Parts Manual REV #3 02/23/06 Heres HOW to GET Help FAX