Stow DFG Series manual Star Flail, Cost 1 Productivity 3 Service Life, Beam Flail

Page 20

ASSEMBLY INSTRUCTIONS/OPERATIONS

the more aggressive the flail configurations, the more coarse the resulting finish and texture.

Many flail configurations are available to meet a wide variety of job applications and surface material specifications. To give additional perspective to each configuration, a rating system of 1 to 10 (10 being highest) has been devised.

FIGURE 6

Star Flail

The star flail is manufactured from high carbon steel that is through hardened for additional service life. It is highly effective for light cleaning or scarifying and delivers a finer surface finish texture. FIGURE 7.

Suggested Applications:

1)Removal of thin coatings and encrusted accumulations.

2)Cleaning concrete and asphaltic surfaces

3)Removing thick material build-ups of greases, paints, oils, vegetable powders and some resins from floors.

4)Light scarifying prior to the application of coatings, toppings or sealers.

FIGURE 7

COST 1 PRODUCTIVITY 3 SERVICE LIFE 1

The star flail should be replaced when the outside diameter is worn to approximately 1-5/16 inch or the inside diameter elongates to approximately 3/4 inch.

Beam Flail

The beam type flail is manufactured from high carbon steel that is through hardened for additional service life. It is highly effective for scabbling or scarifying and delivers medium to coarse surface finish texture. FIGURE 8.

FIGURE 8

Suggested Applications:

1)Medium duty asphalt and concrete scarifying.

2)Descaling steel decks.

3)Removing thick material build-ups of greases, paints, oils, vegetable powders and some resins from floors.

4)Dried, fully cured, carpet and tile adhesive removal.

DFG-SERIES SURFACE GRINDERS	OPERATION AND PARTS MANUAL REV #3 (07/13/06)	PAGE 20

Image 20

Contents Electric Gasoline Page Table of Contents Table of Contents Page Stow Construction Equipment Parts Ordering ProceduresHere’s how to get help Page Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Surface GrinderSafety Precautions Application All Models AssemblyRemoving the Surface Grinder from the Pallet Installing the SG24-1000 Safety and Dust Shield Assembly KIT Before Starting the Engine Filling the Engine Crankcase with OILApplications DFG/G Surface Grinder Filling the DFG/G Series Engine Fuel TankMULTI-ACCESSORY Attachments and Applications OperationTheory of Operation Grinding StonesTungsten Carbide Grinding Block Scarifier BlocksBeam Flail Cost 1 Productivity 3 Service LifeStar Flail Cost 1 Productivity 5 Service Life Cost Productivity Service LifePentagonal Flail Spacer WasherWire brushes Scarifier Block BushingFloor Brushes SCRAPE-R-TACH Industrial Floor Coatings Removal SystemAssembly INSTRUCTIONS/OPERATIONS Follow all safety precautions for the safety solvent Diamond Segment Block Assembly INSTRUCTIONS/OPERATIONS From the Counterrotating Discs Assembly INSTRUCTIONS/OPERATIONS Adjusting the Operator Handle HEIGHT. Application All Models Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Operating the Surface Grinder on the Jobsite Result in Property Damage AND/OR Personal Injury FiureAssembly INSTRUCTIONS/OPERATIONS Definitions of floor flatness and levelness Stopping the DFG/G Series Gasoline Powered Surface GrinderApplication All Models Early Age Grinding How to Define Surface Regularity Defined Versus Random Traffic PatternsTR 34 tolerances for defined traffic floors Assembly INSTRUCTIONS/OPERATIONS Preventative Maintenance Check LIST. Application All Models MAINTENANCE/SERVICEMaintenance/Service Observe all applicable safety precautions for the solvent MAINTENANCE/SERVICE Checking V-BELT Tension and Alignment MAINTENANCE/SERVICE Lubrication Requirements Electric Motor Service Engine ServiceTroubleshooting TroubleshootingOperational PROBLEMS. Application All Models Uneven MULTI-ACCESSORY Attachment WearAccelerated V-BELT Wear Accelerated Bearing Wear AND/OR FailureStorage StorageSpecifications Vacuum Cleaner Connection DiameterMaximum Grinding Width Typical Operator Handle HeightPage Xxxxx only Not Used on Part NameRemarks Qty Description Suggested Spare PartsUnits Gasoline Engine Units Electric Motor Model Operator Handle ASSY. Electric Operator Handle ASSY. ElectricHANDLE, Operator Universal HP Motor onlyCABLE, Long CABLE, ShortOperator Handle ASSY. Gasoline Operator Handle ASSY. GasolineCABLE, Throttle KNOB, Throttle ControlQTY Remarks LEVER, Throttle CONTROL, W/CABLE & KnobElectric Motor Assy Electric Motor AssyMOUNT, Electric Motor HP 50 HZ MotorSCREW, CAP 5/16-18 UNC X 1 Plated WASHER, Flat 5/16, PlatedGasoline Engine Assy Gasoline Engine AssyENGINE, Honda 11 H.P MOUNT, Gasoline EngineCLUTCH, Pulley Assy CAP, OIL DrainWheel Assy Wheel AssyARM, Swing WheelAXLE, Plated WASHER, Flat ¾ PlatedTransmission Assy Transmission AssyFRAME, Main COVER, TransmissionBEARING, Flange WASHER, Lock 5/16 PlatedHead Assy Head AssyDISC, MULTI- Accessory LH DISC, MULTI- Accessory RHBAR, Mounting DISC, MountingSafety and Dust Shield Assy Safety and Dust Shield AssySkirt Assembly SKIRT, GrinderWASHER, Fender 1/4 , Plated STRAP, SkirtScarifier Assy Scarifier AssyHousing BushingNUT, HEX 3/8 UNC, Nylock Plated WEDGE, PlasticSCRAPE-R-TACH Assy HOLDER, Insert MOUNT, RubberSpacer INSERT, Tungsten CarbideGrinding Block Assy Block RingAggress Grinding General PurposeDecals DecalsDecals Part Name QTY Remarks DECAL, WarningDECAL, Operation DECAL, Throttle Sfdclsdp DECAL, Stow LargeSpecial Expediting Service PRICING, Rebates SpecificationsPayment Terms Freight PolicyPage Heres HOW to GET Help FAX