Operation

2 Position Belt Cover - Figure 2 & 3

The belt sander has an aluminum sanding belt cover at the front. When the handle is positioned in the uppermost position, this cover can be raised as shown in Figure 2 (Arrow 1) and locked in this position to:

a.) Improve accessibility to narrow areas.

b.) Allow the use of the smaller diameter front roller to sand with (normally the aluminum cover prevents this when in the “down” position).

c.) Expose the top part of the belt for more versatile sanding (Figure 3).

To lower the belt cover, grasp the flange on the side and move it slightly in the direction shown in Figure 2 (Arrow 2) and return it to its closed position.

Note: The sanding belt cover cannot be locked in its raised position unless the bail handle is in the uppermost position.

WARNING: The sanding belt is exposed when the belt cover is raised. Use extra caution when operating in this mode.

Adjusting The Sanding Belt Tracking - Figure 4

Turn the machine upside down (Figure 4), hold it firmly with one hand, start motor and release switch immediately after observing tracking of sanding belt. If abrasive belt runs outward, turn tracking adjustment knob clockwise and counterclockwise if belt runs inward. Belt life will be greatly increased by keeping the tracking adjustment set properly. To prevent the sanding belt from rubbing against the sander housing, keep the edge of the belt about 7/64 in. (2.7mm) to 13/64 in. (5.1mm) from the housing as shown in figure 4.

Changing The Sanding Belt - Figure 5 & 6

WARNING: To prevent accidental operation, turn off and unplug sander before

changing the sanding belt.

Pull the lever shown in Figure 5 to release the tension on the sanding belt. Pull the sanding belt from the two rollers. Put the new 3 in. x 21 in. (75 x 533mm) sanding belt in position on the front and rear rollers (Figure 6). Ensure that the arrows on the sanding belt and on your belt sander are pointing in the same direction. Push the lever to the rear to tension the sanding belt.WARNING: To reduce the risk of injury, make sure belt is installed with arrows in proper direction of rotation. Failure to do this could result in the belt unraveling creating a hazardous condition.

Dust Collection - Figure 7

WARNING: To prevent accidental operation, turn off and unplug sander before installing the dust bag.

When using your belt sander, dust and grit are produced. It is important to use a dust bag. Connect the dust bag by sliding the plastic opening of the bag down over the dust exhaust port of the sander as shown in Figure 7. To empty the dust bag, remove it from the sander and unzip the bag over a trash container.

Note: A vacuum cleaner attachment is available as a service part at extra cost. To find your nearest Black & Decker Service Center location, refer to the yellow pages directory under “Tools—Electric” or call: 1-800-544-6986.

WARNING: Fire hazard. Collected sanding dust from sanding surface coatings (polyurethane, linseed oil, etc.) can self-ignite in sander dust bag or elsewhere and cause fire. To reduce risk, empty bag frequently and strictly follow sander manual and coating manufacturer’s instructions.

WARNING: Fire hazard. When sanding wood that could contain nails or when sanding metal surfaces, do not use the dust bag or a vacuum cleaner because sparks are generated. Wear safety glasses and a dust mask. Due to the danger of fire, do not use your belt sander to sand magnesium surfaces. Do not use for wet sanding.

Using Your Belt Sander - Figure 8

Always hold belt sander firmly with both hands while sanding as shown in Figure 8. Note that sander bail handle can be adjusted to three different positions as previously discussed. Inversion Stand - An inversion stand is available for this belt sander from your nearest Black & Decker service center as service part number 478700-00. The inversion stand allows the belt sander to be used like a small stationary sander for horizontal sanding. Sanding Frame - A sanding frame as service part number 478705-00. A sanding frame allows for smooth even sanding without gouging.

If you need assistance in locating either of the above service parts, please call 1-800-544-6986.

DS321, Catalog Number DS321 specifications

The Black & Decker DS321 is a powerful and highly versatile steam iron designed to provide an exceptional ironing experience. This model stands out for its combination of advanced features, user-friendly design, and reliable performance.

One of the main features of the Black & Decker DS321 is its robust steam generation capability. The steam iron boasts a powerful steam output that penetrates deep into fabrics, effectively removing wrinkles and creases. This feature is especially beneficial for heavier materials such as denim or linen, making it a great choice for tackling a variety of garments.

Another notable aspect is its lightweight construction. Weighing in at just over three pounds, the DS321 is easy to maneuver and handle, reducing fatigue during extended ironing sessions. The lightweight nature of the iron makes it ideal for individuals of all ages, including those who may find traditional heavy irons cumbersome.

The DS321 comes equipped with a non-stick soleplate, which ensures smooth gliding across different fabric types. This feature allows for efficient ironing without snagging or sticking, thus protecting delicate materials. The soleplate is designed to distribute heat evenly, ensuring consistent results.

Additionally, this steam iron includes a large water tank capacity, which minimizes the need for frequent refills. The easy-fill tank is designed for quick access, making the ironing process more efficient. It also features an automatic shut-off function, providing peace of mind by turning off the iron when left unattended for a certain period, enhancing safety in the household.

The Black & Decker DS321 introduces advanced technologies such as vertical steam, allowing users to steam garments while they are on hangers. This feature is especially useful for curtains, suits, and other items that are difficult to iron flat.

In conclusion, the Black & Decker DS321 is a feature-rich steam iron that combines powerful performance with ease of use. With its steam generation capabilities, lightweight design, non-stick soleplate, and safety features, it caters to all ironing needs, making it a valuable addition to any home. Whether you're a seasoned ironing pro or an occasional user, the DS321 aims to simplify your laundry routine and provide exceptional results.