Grizzly G9860 Belts, Tools Needed Qty, To properly tension the V-belts, To replace the V-belts

Page 37

V-Belts

V-belts will wear and stretch with extended use. Maintaining proper tension of V-belts and making sure they are in good condition will increase the efficiency of the cutterhead and reduce wear on the bearings.

When a V-belt can no longer be properly ten- sioned or is cracked/damaged, replace both V-belts as a matched set.

Tools Needed

Qty

Phillips Screwdriver

1

Wrench or Socket 19mm

1

To properly tension the V-belts:

1.DISCONNECT JOINTER FROM POWER!

2.Remove the rear access motor cover to access the V-belts (see Figure 55).

Cutterhead

Pulley

V-Belts

Mounting

Bolt

Motor Pulley

Figure 55. V-belts and pulleys.

3.Loosen the two motor mounting bolts, then, with assistance, raise or lower the motor assembly until there is the proper tension on the V-belts.

Note: The V-belts are properly tensioned when there is approximately 34" of deflection between the pulleys when moderate pres- sure is applied with your finger, as shown in Figure 56.

EjaaZn

3$4

9Z[aZXi^dc

EjaaZn

Figure 56. The correct amount of V-belt

deflection between the pulleys.

4.When you have properly tensioned the V-belts, re-tighten the motor mounting bolts and re-install the motor access cover.

To replace the V-belts:

1.DISCONNECT JOINTER FROM POWER!

2.Remove the rear access motor cover, then loosen the motor mounting bolts.

3.With assistance, raise the motor assembly up until you can roll the V-belts off the pulleys.

4.Replace the V-belts with a new, matched set, then properly tension them as instructed above.

Extreme Series Jointer (Mfg. Since 9/11)

-35-

Image 37
Contents Extreme Series Jointer Ss ,EAD from Leadbased PAINTS Table of Contents Warranty and Returns Manual Accuracy Contact Info IntroductionMachine Description Identification Model Specification Comparison Safety Instructions for Machinery SafetyZghWZXdbZVYhigVXidc# Children & BYSTANDERS. @ZZe XaYgZcAdditional Safety Instructions for Jointers Availability Power SupplyFull-Load Current Rating Circuit InformationG9953ZXF Circuit Requirements for 220V Operation Circuit Requirements For G9953 G9953ZXG9953ZXF Circuit Requirements for 440V Operation Grounding Requirements Model G9953ZXF 440V ConversionExtension Cords G9860, G9860ZX, G9953, & G9953ZX Only Replacing Contactor & Overload RelayReplacing Control Panel Light Bulbs Rewiring MotorNeeded for Setup SetupUnpacking Description QtyInventory Figure Qty Inventory Clean UpSite Considerations Placement LocationMounting to Shop Floor Floor LoadMoving Assembling Jointer Using Machine MountsMoving & Placing Jointer Infeed table stop bolt viewed from Underneath the table Installing Fence G9953/G9953ZX/ G9953ZXF Installing Fence G9860/G960ZXStep To set the outfeed table height Setting OutfeedModels G9953, G9953ZX, & G9953ZXF Cutter edge at top-dead-center Page OFF Button Dust Collection Test RunTo connect a dust collection hose Factory adjustments that should be verified Recommended AdjustmentsBasic Controls OperationsControl Panel Fence Controls Table ControlsCutterhead Brake G9953/G9953ZX/ G9953ZXF Only Stock Inspection Requirements Follow these rules when choosing and joint- ing stock#/22%#4 Surface Plane on a Thickness Planer Squaring StockTo surface plane the workpiece on the joint- er Surface PlanningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingDispoz-A-BladeHolder and Knife AccessoriesEye protection assortment Cleaning Protecting MaintenanceSchedule Lubrication Fence Assembly Pivot PointsCutterhead Bearing Blocks Table Elevation Gears & LeadscrewTools Needed Qty BeltsTo properly tension the V-belts To replace the V-beltsTroubleshooting ServiceMotor & Electrical Operations Rotating/Replacing Cutterhead Inserts Infeed Table Stop BoltTo rotate or replace a spiral cutterhead InsertAir Pressure Torque Wrench Adjusting/Replacing Cutterhead KnivesChecking knife height with a To adjust or replace the knivesPage Models G9860 & G9860ZX Setting Fence StopsTo set the 90 fence stop To set the 45 fence stopModels G9953, G9953ZX, G9953ZXF Adjusting Outfeed Table Parallelism Adjusting Table ParallelismCZZY Then make sure the table lock is Adjusting Infeed Table ParallelismGZVg AZi Wiring Safety Instructions WiringShock Hazard G9860 & G9860ZX Wiring DiagramG9953 & G9953ZX Wiring Diagram G9953ZXF 220V Wiring Diagram G9953ZXF 440V Wiring Diagram Parts G9860/G9860ZX Cabinet Breakdown Parts ListMotor Cutterhead BreakdownG9860ZX Cutterhead & Motor Parts List G9860 Cutterhead & Motor Parts ListG9860/G9860ZX Fence Breakdown G9860ZX Fence Parts List G9860 Fence Parts List+ && &% G9860/G9860ZX Table Breakdown Parts ListG9860/G9860ZX Handwheel Breakdown Parts List G9953/G9953ZX/G9953ZXF Cabinet Breakdown & Parts List Breakdown CutterheadG9953ZX/G9953ZXF Cutterhead Parts List G9953 Cutterhead Parts ListG9953/G9953ZX/G9953ZXF Breakdown G9953/G9953ZX/G9953ZXF Fence Parts List G9953/G9953ZX/G9953ZXF Table Breakdown G9953/G9953ZX/G9953ZXF Table Parts List G9953/G9953ZX/G9953ZXF Handwheel Breakdown & Parts List G9953ZXF Motor Parts List G9953/G9953ZX Motor Parts ListG9953/G9953ZX/G9953ZXF Motor Breakdown Label Placement Extreme Series Jointer Mfg. Since 9/11 10. 8dbbZcih Warranty Card99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns Order Hours a DAY
Related manuals
Manual 56 pages 43.38 Kb Manual 76 pages 30.5 Kb Manual 56 pages 10.1 Kb Manual 56 pages 10.1 Kb

G9860 specifications

The Grizzly G9859, G9860, G9861, and G9860ZX are an impressive lineup of high-quality, precision-engineered woodworking machines designed for both hobbyists and professional woodworkers. These machines embody Grizzly's commitment to advanced technology and innovative design, making them essential tools in any woodshop.

The G9859 is a versatile horizontal band saw that offers users enhanced cutting capabilities with its powerful motor and robust construction. One of its standout features is the precision-machined guide system, which ensures accurate cuts every time. The saw's adjustable cutting height and width settings allow it to handle a variety of materials, making it ideal for both intricate and large-scale projects. The G9859 also comes equipped with a heavy-duty steel frame that minimizes vibration, promoting smooth operation.

Next in the lineup is the G9860, a remarkable vertical band saw that excels in both performance and user-friendliness. Featuring an oversized cast iron table, the G9860 provides ample workspace for larger projects. The table can be easily adjusted for bevel cuts, making it a versatile choice for woodworkers looking to enhance their skill set. The saw’s integrated light and adjustable blade guards improve visibility and safety while working.

The G9861 is a powerful jointer that offers professional-grade performance. With its quick-adjust infeed and outfeed tables, this machine makes jointing boards a breeze. The G9861 features a helical cutter head, ensuring a cleaner cut and minimizing noise during operation. This feature is particularly beneficial for users looking for a finish quality that stands out in any woodworking project.

Lastly, the G9860ZX combines the features of a table saw and a cabinet saw, catering to users who need both functionalities. Its robust construction, paired with an impressive motor capacity, allows for smooth and efficient cuts. The G9860ZX is designed with a quick-release fence system, making adjustments fast and easy.

Overall, the Grizzly G9859, G9860, G9861, and G9860ZX represent the forefront of woodworking technology. With features that prioritize precision, safety, and ease of use, these machines are excellent additions to any workshop, whether for small projects or large-scale production runs. With Grizzly's reputation for quality, users can trust these models to deliver performance that meets and exceeds expectations in woodworking applications.