Grizzly G9860 owner manual Adjusting Infeed Table Parallelism, Then make sure the table lock is

Page 48

8.Loosen the cap screw in the center of the outfeed table adjustment bolt three full turns, then loosen the set screw that is directly underneath the adjustment bolt (see

Figure 71).

Note: Both of these screws are used to lock the adjustment bolt in place.

11.

When the outfeed table height is correct

 

and parallel to the cutterhead, re-tighten the

 

adjustment bolt cap screw and set screw (see

 

Figure 71), then make sure the table lock is

 

tightened.

12.

Loosen the jam nut and adjust the outfeed

 

stop bolt underneath the table so that it just

 

touches the bottom of the tables, as shown in

 

Figure 72, then re-tighten the jam nut.

8Vb

HZiHXgZl

IVWaZ

6Y_jhibZci 7dai

8Ve HXgZl

Note: When adjusted to the correct outfeed

table height, use the stop bolt for a conve-

nient method of ensuring the outfeed table is

set at the proper height.

Stop Bolt

Figure 71. Illustration of the table adjustment

bolt components.

Note: The goal of the next step is to bring the outfeed table parallel to the cutterhead body from front-to-back by raising or lowering the front corner of the outfeed table.

9.The adjustment bolt shaft is cam-shaped, as shown in Figure 71, and connects the table to the lifting arm. Rotate the adjustment bolt in very small increments to raise or lower the front corner of the outfeed table until the surface is the correct height above the cutterhead, as instructed in Step 4.

10.Re-check the table height at the back edge of the table, as instructed in Step 4.

—If the table height is correct from front-to- back, no further adjustments are neces- sary. Go to Step 11 to finish this proce- dure.

—If the table height from front-to-back is not correct and the same, loosen the table lock and use the handwheel to bring the back of the table to the correct height above the cutterhead body, then repeat Step 9. Continue this process until the table height is correct and the same from front-to- back.

-46-

Jam Nut

Figure 72. Outfeed table stop bolt (viewed from

underneath the table).

13.When the Adjusting Outfeed Table Parallelism procedure is successfully com- pleted, proceed to Adjusting Infeed Table Parallelism.

Adjusting Infeed Table Parallelism

1.Make sure that all steps in the Adjusting Outfeed Table Parallelism procedure have been successfully completed and that the jointer is still disconnected from power.

2.Make sure the table surfaces and the preci- sion straightedge are free from any debris that would interfere with taking measurements, then place the straightedge equally over the back of the outfeed and infeed tables.

Note: Make sure the straightedge is not in contact with a knife or insert.

Extreme Series Jointer (Mfg. Since 9/11)

Image 48
Contents Extreme Series Jointer Ss ,EAD from Leadbased PAINTS Table of Contents Warranty and Returns Introduction Manual Accuracy Contact InfoMachine Description Identification Model Specification Comparison Safety Safety Instructions for MachineryChildren & BYSTANDERS. @ZZe XaYgZc ZghWZXdbZVYhigVXidc#Additional Safety Instructions for Jointers Power Supply AvailabilityFull-Load Current Rating Circuit InformationCircuit Requirements For G9953 G9953ZX G9953ZXF Circuit Requirements for 220V OperationG9953ZXF Circuit Requirements for 440V Operation Model G9953ZXF 440V Conversion Grounding RequirementsExtension Cords G9860, G9860ZX, G9953, & G9953ZX Only Replacing Contactor & Overload RelayRewiring Motor Replacing Control Panel Light BulbsSetup Needed for SetupUnpacking Description QtyInventory Clean Up Inventory Figure QtyPlacement Location Site ConsiderationsMounting to Shop Floor Floor LoadUsing Machine Mounts Moving Assembling JointerMoving & Placing Jointer Infeed table stop bolt viewed from Underneath the table Installing Fence G9860/G960ZX Installing Fence G9953/G9953ZX/ G9953ZXFStep Setting Outfeed To set the outfeed table heightModels G9953, G9953ZX, & G9953ZXF Cutter edge at top-dead-center Page Dust Collection Test Run OFF ButtonTo connect a dust collection hose Recommended Adjustments Factory adjustments that should be verifiedOperations Basic ControlsControl Panel Table Controls Fence ControlsCutterhead Brake G9953/G9953ZX/ G9953ZXF Only Follow these rules when choosing and joint- ing stock Stock Inspection Requirements#/22%#4 Squaring Stock Surface Plane on a Thickness PlanerSurface Planning To surface plane the workpiece on the joint- erEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerAccessories Dispoz-A-BladeHolder and KnifeEye protection assortment Maintenance Cleaning ProtectingSchedule Fence Assembly Pivot Points LubricationCutterhead Bearing Blocks Table Elevation Gears & LeadscrewBelts Tools Needed QtyTo properly tension the V-belts To replace the V-beltsService TroubleshootingMotor & Electrical Operations Infeed Table Stop Bolt Rotating/Replacing Cutterhead InsertsTo rotate or replace a spiral cutterhead InsertAdjusting/Replacing Cutterhead Knives Air Pressure Torque WrenchTo adjust or replace the knives Checking knife height with aPage Setting Fence Stops Models G9860 & G9860ZXTo set the 90 fence stop To set the 45 fence stopModels G9953, G9953ZX, G9953ZXF Adjusting Table Parallelism Adjusting Outfeed Table ParallelismCZZY Adjusting Infeed Table Parallelism Then make sure the table lock isGZVg AZi Wiring Wiring Safety InstructionsG9860 & G9860ZX Wiring Diagram Shock HazardG9953 & G9953ZX Wiring Diagram G9953ZXF 220V Wiring Diagram G9953ZXF 440V Wiring Diagram G9860/G9860ZX Cabinet Breakdown Parts List PartsCutterhead Breakdown MotorG9860 Cutterhead & Motor Parts List G9860ZX Cutterhead & Motor Parts ListG9860/G9860ZX Fence Breakdown G9860 Fence Parts List G9860ZX Fence Parts ListG9860/G9860ZX Table Breakdown Parts List + && &%G9860/G9860ZX Handwheel Breakdown Parts List G9953/G9953ZX/G9953ZXF Cabinet Breakdown & Parts List Cutterhead BreakdownG9953 Cutterhead Parts List G9953ZX/G9953ZXF Cutterhead Parts ListG9953/G9953ZX/G9953ZXF Breakdown G9953/G9953ZX/G9953ZXF Fence Parts List G9953/G9953ZX/G9953ZXF Table Breakdown G9953/G9953ZX/G9953ZXF Table Parts List G9953/G9953ZX/G9953ZXF Handwheel Breakdown & Parts List G9953/G9953ZX Motor Parts List G9953ZXF Motor Parts ListG9953/G9953ZX/G9953ZXF Motor Breakdown Label Placement Extreme Series Jointer Mfg. Since 9/11 Warranty Card 10. 8dbbZcih99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns Order Hours a DAY
Related manuals
Manual 56 pages 43.38 Kb Manual 76 pages 30.5 Kb Manual 56 pages 10.1 Kb Manual 56 pages 10.1 Kb

G9860 specifications

The Grizzly G9859, G9860, G9861, and G9860ZX are an impressive lineup of high-quality, precision-engineered woodworking machines designed for both hobbyists and professional woodworkers. These machines embody Grizzly's commitment to advanced technology and innovative design, making them essential tools in any woodshop.

The G9859 is a versatile horizontal band saw that offers users enhanced cutting capabilities with its powerful motor and robust construction. One of its standout features is the precision-machined guide system, which ensures accurate cuts every time. The saw's adjustable cutting height and width settings allow it to handle a variety of materials, making it ideal for both intricate and large-scale projects. The G9859 also comes equipped with a heavy-duty steel frame that minimizes vibration, promoting smooth operation.

Next in the lineup is the G9860, a remarkable vertical band saw that excels in both performance and user-friendliness. Featuring an oversized cast iron table, the G9860 provides ample workspace for larger projects. The table can be easily adjusted for bevel cuts, making it a versatile choice for woodworkers looking to enhance their skill set. The saw’s integrated light and adjustable blade guards improve visibility and safety while working.

The G9861 is a powerful jointer that offers professional-grade performance. With its quick-adjust infeed and outfeed tables, this machine makes jointing boards a breeze. The G9861 features a helical cutter head, ensuring a cleaner cut and minimizing noise during operation. This feature is particularly beneficial for users looking for a finish quality that stands out in any woodworking project.

Lastly, the G9860ZX combines the features of a table saw and a cabinet saw, catering to users who need both functionalities. Its robust construction, paired with an impressive motor capacity, allows for smooth and efficient cuts. The G9860ZX is designed with a quick-release fence system, making adjustments fast and easy.

Overall, the Grizzly G9859, G9860, G9861, and G9860ZX represent the forefront of woodworking technology. With features that prioritize precision, safety, and ease of use, these machines are excellent additions to any workshop, whether for small projects or large-scale production runs. With Grizzly's reputation for quality, users can trust these models to deliver performance that meets and exceeds expectations in woodworking applications.