Powermatic PJ882 Warranty and Service, More Information WMH Tool Group Warranty

Page 2

This manual has been prepared for the owner and operators of a Model PJ-882 Jointer. Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and efficiency from your jointer and to aid in using it safely, please read this manual thoroughly and follow the instructions carefully.

Warranty and Service

WMH Tool Group warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Repair Stations located throughout the United States can provide quick service or information.

In most cases, a WMH Tool Group Repair Station can assist in authorizing repair work, obtaining parts, or perform routine or major maintenance repair on your Powermatic product.

For the name of an Authorized Repair Station in your area, please call 1-800-274-6848, or visit our web site at www.wmhtoolgroup.com

More Information

Remember, WMH Tool Group is consistently adding new products to the line. For complete, up-to-date product information, check with your local WMH Tool Group distributor, or visit our web site at www.wmhtoolgroup.com

WMH Tool Group Warranty

WMH Tool Group makes every effort to assure that its products meet high quality and durability standards and warrants to the original retail consumer/purchaser of our products that each product be free from defects in materials and workmanship as follows: 1 YEAR LIMITED WARRANTY ON ALL PRODUCTS UNLESS SPECIFIED OTHERWISE. This Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, repair or alterations outside our facilities, or to a lack of maintenance.

WMH TOOL GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD SPECIFIED ABOVE, BEGINNING FROM THE DATE THE PRODUCT WAS PURCHASED AT RETAIL. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. IN NO EVENT SHALL WMH TOOL GROUP BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

To take advantage of this warranty, the product or part must be returned for examination, postage prepaid, to an Authorized Repair Station designated by our office. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection discloses a defect, we will either repair or replace the product at our discretion, or refund the purchase price if we cannot readily and quickly provide a repair or replacement. We will return the repaired product or replacement at WMH Tool Group’s expense, but if it is determined there is no defect, or that the defect resulted from causes not within the scope of WMH Tool Group’s warranty, then the user must bear the cost of storing and returning the product. This warranty gives you specific legal rights; you may also have other rights, which vary from state to state.

WMH Tool Group sells through distributors only. Members of the WMH Tool Group reserve the right to effect at any time, without prior notice, alterations to parts, fittings and accessory equipment, which they may deem necessary for any reason whatsoever.

2

Image 2
Contents Inch Parallelogram Jointer Part No. M-1610079Warranty and Service More Information WMH Tool Group WarrantyTable of Contents Page Page Page Specifications Introduction DescriptionContents of the Shipping Container UnpackingInstallation and Assembly Tools required for assemblyInstalling Switch Arm Installing Cutterhead GuardGrounding Instructions Dust CollectionExtension cords Volt, Single Phase OperationThree Phase Operation Adjustments Drive Belt TensionTo slide fence forward or backward Drive Belt ReplacementFence Movement To tilt fence forwardFence Stops Setting the 90 StopSetting the 45 Forward Stop To tilt fence backwardFence Removal Table and Knife AdjustmentsSetting the 45 Backward Stop Locking HandlesSetting Tables Parallel Back of outfeed table shown Page Page Page Infeed Table Depth Stop Setting Infeed Table Depth of CutOutfeed Table Stop Screws Infeed Table Stop Screws Replacing Knives in the CutterheadEliminating Play in Tables Operating ControlsOperation Surfacing Hand PlacementAlways use a hold down or push block when surfacing stock Edge JointingJointing Warped Surfaces RabbetingJointing Short or Thin Work BevelingDirection of Grain Skewing Shear CuttingMaintenance Sharpening KnivesUse caution when working around sharp knives Cutterhead RepairsProbable Cause Remedy Troubleshooting Operating ProblemsTrouble Troubleshooting Mechanical and Electrical Problems Trouble Probable Cause Remedy Optional AccessoriesReplacement Parts Parts List Cutterhead Assembly Index No. Part No Description Size QtyParts List Fence Assembly Fence Assembly Parts List Outfeed Table and Base Assembly Outfeed Table and Base Assembly Parts List Infeed Table Assembly PJ882-246 Infeed Table Assembly Parts List Stand Assembly TS-081B022 Stand Assembly Electrical Connections 1 Phase, 230 Volt Electrical Connections 3 Phase, 230 Volt Electrical Connections 3 Phase, 460 Volt Page WMH Tool Group