Powermatic PJ882 operating instructions Introduction Description, Specifications

Page 7

Introduction

This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures for a Model PJ-882 Jointer. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. If there are any questions or comments, please contact either your local supplier or WMH Tool Group. WMH Tool Group can also be reached at our web site: www.wmhtoolgroup.com.

Description

The Model PJ-882 Jointer is built upon a parallelogram design. This design allows independent adjustment of sections of the infeed and outfeed tables to ensure the tables remain parallel with the cutterhead and with each other. The fence has a tilting capacity of 45 degrees forward and backward, with positive stops.

Specifications

 

(1 Phase Model)

(3 Phase Model)

Model Number

PJ-882

...................................................PJ-882

Stock Number

1610079

................................................ 1610080

Maximum Cutting Width (in.)

8

............................................................8

Maximum Cutting Depth (in.)

1/2

......................................................... 1/2

Rabbeting Capacity (in.)

1/2

......................................................... 1/2

Cutterhead Speed (RPM)

7,000

..................................................... 7,000

Motor

TEFC, 2HP, 1Ph, 230V

................... TEFC, 3HP, 3Ph, 230/460V

 

 

(prewired 230V)

Starter

magnetic

................................................magnetic

Number of Knives

3

............................................................3

Cuts Per Minute

21,000

................................................... 21,000

Cutterhead Diameter (in.)

3-1/16

.................................................... 3-1/16

Table Surface (L x W)(in.)

83 x 8

.................................................... 83 x 8

Fence Size (L x H)(in.)

38 x 4-3/4

.............................................. 38 x 4-3/4

Fence Tilt (deg.)

45 forward, 45 backward

........................45 forward, 45 backward

Positive Stops (deg.)

-45, 90, +45

........................................... -45, 90, +45

Dust Chute Diameter (in.)

4

............................................................4

Overall Dimensions (L x W x H)(in.)

84 x 28 x 44

...........................................84 x 28 x 44

Net Weight – approx. (lbs.)

610

........................................................ 610

Shipping Weight – approx. (lbs.)

744

........................................................ 744

The above specifications were current at the time this manual was published, but because of our policy of continuous improvement, WMH Tool Group reserves the right to change specifications at any time and without prior notice, without incurring obligations.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Part No. M-1610079 Inch Parallelogram JointerMore Information WMH Tool Group Warranty Warranty and ServiceTable of Contents Page Page Page Introduction Description SpecificationsUnpacking Contents of the Shipping ContainerTools required for assembly Installation and AssemblyInstalling Cutterhead Guard Installing Switch ArmDust Collection Grounding InstructionsThree Phase Operation Volt, Single Phase OperationExtension cords Drive Belt Tension AdjustmentsTo tilt fence forward Drive Belt ReplacementFence Movement To slide fence forward or backwardTo tilt fence backward Setting the 90 StopSetting the 45 Forward Stop Fence StopsLocking Handles Table and Knife AdjustmentsSetting the 45 Backward Stop Fence RemovalSetting Tables Parallel Back of outfeed table shown Page Page Page Outfeed Table Stop Screws Setting Infeed Table Depth of CutInfeed Table Depth Stop Replacing Knives in the Cutterhead Infeed Table Stop ScrewsOperation Operating ControlsEliminating Play in Tables Edge Jointing Hand PlacementAlways use a hold down or push block when surfacing stock SurfacingBeveling RabbetingJointing Short or Thin Work Jointing Warped SurfacesSkewing Shear Cutting Direction of GrainSharpening Knives MaintenanceCutterhead Repairs Use caution when working around sharp knivesTrouble Troubleshooting Operating ProblemsProbable Cause Remedy Troubleshooting Mechanical and Electrical Problems Replacement Parts Optional AccessoriesTrouble Probable Cause Remedy Index No. Part No Description Size Qty Parts List Cutterhead AssemblyParts List Fence Assembly Fence Assembly Parts List Outfeed Table and Base Assembly Outfeed Table and Base Assembly Parts List Infeed Table Assembly PJ882-246 Infeed Table Assembly Parts List Stand Assembly TS-081B022 Stand Assembly Electrical Connections 1 Phase, 230 Volt Electrical Connections 3 Phase, 230 Volt Electrical Connections 3 Phase, 460 Volt Page WMH Tool Group
Top Page Image Contents