Powermatic 1285 Warranty and Service, More Information WMH Tool Group Warranty

Page 2

This manual has been prepared for the owner and operators of a Powermatic Model 1285 Jointer. Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and efficiency from your jointer and to aid in using it safely, please read this manual thoroughly and follow the instructions carefully.

Warranty and Service

WMH Tool Group warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Center located throughout the United States can provide quick service or information.

In most cases, a WMH Tool Group Service Center can assist in authorizing repair work, obtaining parts, or perform routine or major maintenance repair on your Powermatic product.

For the name of an Authorized Service Center in your area, please call 1-800-274-6848, or visit our web site at www.wmhtoolgroup.com

More Information

Remember, WMH Tool Group is consistently adding new products to the line. For complete, up-to-date product information, check with your local WMH Tool Group distributor, or visit our web site at www.wmhtoolgroup.com

WMH Tool Group Warranty

WMH Tool Group makes every effort to assure that its products meet high quality and durability standards and warrants to the original retail consumer/purchaser of our products that each product be free from defects in materials and workmanship as follows: 1 YEAR LIMITED WARRANTY ON ALL PRODUCTS UNLESS SPECIFIED OTHERWISE. This Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, repair or alterations outside our facilities, or to a lack of maintenance.

WMH TOOL GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD SPECIFIED ABOVE, BEGINNING FROM THE DATE THE PRODUCT WAS PURCHASED AT RETAIL. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. IN NO EVENT SHALL WMH TOOL GROUP BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

To take advantage of this warranty, the product or part must be returned for examination, postage prepaid, to an Authorized Service Center designated by our office. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection discloses a defect, we will either repair or replace the product at our discretion, or refund the purchase price if we cannot readily and quickly provide a repair or replacement. We will return the repaired product or replacement at WMH Tool Group’s expense, but if it is determined there is no defect, or that the defect resulted from causes not within the scope of WMH Tool Group’s warranty, then the user must bear the cost of storing and returning the product. This warranty gives you specific legal rights; you may also have other rights, which vary from state to state.

WMH Tool Group sells through distributors only. Members of the WMH Tool Group reserve the right to effect at any time, without prior notice, alterations to parts, fittings and accessory equipment, which they may deem necessary for any reason whatsoever.

2

Image 2
Contents Jointer Part No. M-0460216Warranty and Service More Information WMH Tool Group WarrantyTable of Contents Page Figure a Page Introduction Specifications 90, 45 right, 45 leftContents of the Shipping Container UnpackingTools need for assembly AssemblyFence Installation Dust Hood Switch ArmGrounding Instructions Voltage Conversion Extension cordsDrive Belt Tension AdjustmentsSetting Outfeed Table Height Page Setting Infeed Table Height Depth of Cut Replacing and Setting Knives Straight CutterheadPage Replacing Knife Inserts Helical Cutterhead To tilt fence forward Fence AdjustmentsTo check and adjust the 90-degree stop To tilt fence backwardOperation To check and adjust the 45-degree stopOperating Controls Cutter Guard TensionSurfacing Hand PlacementEdge Jointing RabbetingDirection of Grain Jointing Warped SurfacesJointing Short or Thin Work BevelingCutterhead Repairs MaintenanceLubrication Knife Inserts Helical Cutterhead Whetting Knives Straight Cutterhead Probable Cause Remedy Troubleshooting Operating ProblemsTrouble Troubleshooting Mechanical and Electrical Problems Trouble Probable Cause RemedyIf electric motor is suspect, you have Optional Accessories Replacement PartsParts List Stand Assembly Index No. Part No Description Size QtyStand Assembly Parts List Table Assembly Table Assembly Parts List Motor Pulley Assembly Motor Pulley Assembly Parts List Cutterhead Guard Assembly Cutterhead Guard Assembly Parts List Straight Cutterhead Assembly PJ1285-KSGAStraight Cutterhead Assembly Parts List Helical Cutterhead Assembly Helical Cutterhead Assembly Parts List Fence Assembly Fence Assembly Electrical Connections 1 Phase Electrical Connections 3 Phase WMH Tool Group
Related manuals
Manual 40 pages 39.08 Kb