RIDGID R888 manual Volts, 60 Hz, AC only

Page 14

OPERATION

THE FOLLOWING INSTRUCTIONS ARE FOR RIDGID NICKEL-CADMIUM BATTERY PACKS AND CHARGERS.

Battery packs for this tool are shipped in a low charge condition to prevent possible problems. Therefore, you should charge the pack until the light on the front of the charger changes from flashing green to continuous green.

NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged. This is normal for nickel-cadmium batteries.

TO CHARGE

Charge the battery pack only with the charger provided. Make sure the power supply is normal household voltage,

120 volts, 60 Hz, AC only.

Connect the charger to a power supply.

Attach the battery pack to the charger by aligning the raised ribs on the battery pack with the grooves in the charger, then slide the battery pack onto the charger. See

Figure 7.

The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.

Do not place the charger in an area of extreme heat or cold. It will work best at normal room temperature.

For average charge times, refer to the chart on the following page.

When the batteries become fully charged, unplug the charger from the power supply and remove the battery pack.

CHARGING A HOT BATTERY PACK

When using the tool continuously, the batteries in the battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, the green LED will be off and the red LED will begin flashing.

When the battery pack cools down to approximately 104°F (40°C), the charger will automatically begin fast charge mode.

CHARGING A COOL BATTERY PACK

If the battery pack is below normal temperature range, the red LED will begin flashing and the green LED will be off. When the battery warms to a temperature of more than 41°F (5°C), the charger will automatically begin fast charge mode. NOTE: Refer to CHARGING THE BATTERY PACK for normal recharging of batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest repair center for electrical check. For the location of your nearest repair center, please call 1-866-539-1710.

Fig. 7

RED GREEN

LED LED POWER INDICATOR

EVALUATE

INDICATOR

DEFECTIVE

INDICATOR

CHARGING

INDICATOR

FULL

INDICATOR

Fig. 8

14

Image 14
Contents OPERATOR’S Manual Table of Contents IntroductionElectrical Safety General Safety RulesWork Area Safety Personal SafetyService Specific Safety RulesBattery Tool USE and Care Important Safety Instructions Safety Rules for ChargerSymbols Name DESIGNATION/EXPLANATIONSymbol Signal Meaning Features Product SpecificationsChip Exhaust Depth Adjustment KnobKnow Your Hand Planer Edge GUIDE/RABBET GuideUnpacking AssemblyINSTALLING/REMOVING the Dust BAG Packing ListOperation ApplicationsCharging a Cool Battery Pack Charge Level IndicatorCharging a HOT Battery Pack To ChargeLED Battery RED Green Action Indicator Pack LED Function of Ridgid 24V LITHIUM-ION ChargerVolts, 60 Hz, AC only LED Function of Ridgid NICKEL-CADMIUM Chargers STARTING/STOPPING the Planer To Install Battery PackTo Remove Battery Pack Planing Depth To set the planing depthOperating the Planer Dust BAG Clamp WorkpieceAttaching the Edge Guide for Planing Edges ChamferingPlaning Edges and Making Rabbet Cuts Making Rabbet Cuts Planing EdgesAttaching the Edge Guide for Making Rabbet Cuts Battery Pack Removal and Preparation for Recycling MaintenanceGeneral Maintenance BatteriesReplacing Blades See Figures 18Cleaning the Chip Exhaust and EMPTY- ING the Dust BAG Replacing the BeltPage What is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information

R888 specifications

The RIDGID R888 is a powerful tool that continues to cement its reputation among professionals and DIY enthusiasts alike. This advanced cordless impact wrench is designed to tackle a wide array of applications, making it a standout choice for both construction and home improvement projects.

One of the key features of the RIDGID R888 is its robust 18V motor, which delivers an impressive torque output. With a torque rating of up to 600 ft-lbs of nut-busting torque, this tool can handle loosening and fastening tasks that require significant force, such as working with heavy machinery or automotive bolts. The ability to deliver high torque in a compact design makes the R888 versatile for various tasks.

The R888 also incorporates advanced brushless motor technology. This not only enhances the tool's efficiency but also extends its overall lifespan compared to traditional brushed motors. The brushless design provides smoother operation, reducing friction and heat buildup. As a result, the tool operates cooler, which is a crucial factor during extended use.

Another standout characteristic of the RIDGID R888 is its ergonomic design. Equipped with a comfortable grip and a lightweight construction, this impact wrench minimizes user fatigue, allowing for longer periods of operation without discomfort. The tool also features an integrated LED light, improving visibility in dark or confined spaces, which is particularly beneficial when working under vehicles or in poorly lit areas.

Moreover, the R888 includes a 3-speed setting and a snug-fit ½ inch anvil, providing versatility for different tasks. The ability to adjust speed allows users to select the appropriate power for a range of jobs, from delicate assembly tasks to heavy-duty applications. Each speed setting is easy to switch, allowing seamless transitions as needed.

Lastly, the RIDGID R888 is backed by the manufacturer’s lifetime service agreement, which includes free parts and service for the life of the tool, underscoring RIDGID’s commitment to quality and customer satisfaction.

In summary, the RIDGID R888 combines powerful performance, innovative technology, and user-friendly design. Its features and characteristics make it an invaluable addition for anyone looking to increase productivity and efficiency in their work.