RIDGID R888 manual General Maintenance, Batteries

Page 21

MAINTENANCE

WARNING:

When servicing use only identical RIDGID replacement parts. Use of any other parts may create a hazard or cause product damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.

WARNING:

To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at a RIDGID authorized service center.

BATTERIES

This tool will accept 24V lithium-ion batteries or 18V nickel-

BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING

cadmium batteries. Length of service from each charging will depend on the type of work you are doing.

The batteries for this tool have been designed to provide maximum trouble-free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn.

To obtain the longest possible battery life, we suggest the following:

For lithium-ion batteries:

Li - Ion

To preserve natural resources, please recycle or dispose of batteries properly.

This product uses lithium-ion or nickel- cadmium batteries. Local, state or federal laws may prohibit disposal of batteries in ordinary trash.

Consult your local waste authority for information regarding available recycling and/or disposal options.

Remove the battery pack from the charger once it is fully charged and ready for use.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 80°F and away from moisture.

Store battery packs in a 30%-50% charged condition.

Every six months of storage, charge the pack as normal.

For nickel-cadmium batteries:

Remove the battery pack from the charger once it is fully charged and ready for use.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 80°F.

Store battery packs in a “discharged” condition.

WARNING:

Upon removal, cover the battery pack’s terminals with heavy-duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its components. Lithium-ion and nickel- cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents OPERATOR’S Manual Introduction Table of ContentsWork Area Safety General Safety RulesElectrical Safety Personal SafetySpecific Safety Rules Battery Tool USE and CareService Safety Rules for Charger Important Safety InstructionsName DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning Product Specifications FeaturesKnow Your Hand Planer Depth Adjustment KnobChip Exhaust Edge GUIDE/RABBET GuideINSTALLING/REMOVING the Dust BAG AssemblyUnpacking Packing ListApplications OperationCharging a HOT Battery Pack Charge Level IndicatorCharging a Cool Battery Pack To ChargeLED Function of Ridgid 24V LITHIUM-ION Charger LED Battery RED Green Action Indicator PackVolts, 60 Hz, AC only LED Function of Ridgid NICKEL-CADMIUM Chargers To Install Battery Pack To Remove Battery PackSTARTING/STOPPING the Planer To set the planing depth Planing DepthDust BAG Clamp Workpiece Operating the PlanerChamfering Planing Edges and Making Rabbet CutsAttaching the Edge Guide for Planing Edges Planing Edges Attaching the Edge Guide for Making Rabbet CutsMaking Rabbet Cuts General Maintenance MaintenanceBattery Pack Removal and Preparation for Recycling BatteriesSee Figures 18 Replacing BladesReplacing the Belt Cleaning the Chip Exhaust and EMPTY- ING the Dust BAGPage DAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredCustomer Service Information

R888 specifications

The RIDGID R888 is a powerful tool that continues to cement its reputation among professionals and DIY enthusiasts alike. This advanced cordless impact wrench is designed to tackle a wide array of applications, making it a standout choice for both construction and home improvement projects.

One of the key features of the RIDGID R888 is its robust 18V motor, which delivers an impressive torque output. With a torque rating of up to 600 ft-lbs of nut-busting torque, this tool can handle loosening and fastening tasks that require significant force, such as working with heavy machinery or automotive bolts. The ability to deliver high torque in a compact design makes the R888 versatile for various tasks.

The R888 also incorporates advanced brushless motor technology. This not only enhances the tool's efficiency but also extends its overall lifespan compared to traditional brushed motors. The brushless design provides smoother operation, reducing friction and heat buildup. As a result, the tool operates cooler, which is a crucial factor during extended use.

Another standout characteristic of the RIDGID R888 is its ergonomic design. Equipped with a comfortable grip and a lightweight construction, this impact wrench minimizes user fatigue, allowing for longer periods of operation without discomfort. The tool also features an integrated LED light, improving visibility in dark or confined spaces, which is particularly beneficial when working under vehicles or in poorly lit areas.

Moreover, the R888 includes a 3-speed setting and a snug-fit ½ inch anvil, providing versatility for different tasks. The ability to adjust speed allows users to select the appropriate power for a range of jobs, from delicate assembly tasks to heavy-duty applications. Each speed setting is easy to switch, allowing seamless transitions as needed.

Lastly, the RIDGID R888 is backed by the manufacturer’s lifetime service agreement, which includes free parts and service for the life of the tool, underscoring RIDGID’s commitment to quality and customer satisfaction.

In summary, the RIDGID R888 combines powerful performance, innovative technology, and user-friendly design. Its features and characteristics make it an invaluable addition for anyone looking to increase productivity and efficiency in their work.
Top Page Image Contents