Powermatic 54A, 54HH operating instructions

Page 4

1.Read and understand the entire owner's manual before attempting assembly or operation.

2.Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

3.Replace the warning labels if they become obscured or removed.

4.This woodworking Jointer is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a jointer, do not use until proper training and knowledge have been obtained.

5.Do not use this machine for other than its intended use. If used for other purposes, Powermatic disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.

6.Always wear approved safety glasses/face shields while using this jointer. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.

7.Before operating this machine, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.

8.Wear ear protectors (plugs or muffs) during extended periods of operation.

9.Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•Lead from lead based paint.

•Crystalline silica from bricks, cement and other masonry products.

•Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.

10.Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

11.Make certain the switch is in the OFF position before connecting the machine to the power source.

12.Make certain the machine is properly grounded.

13.Make all machine adjustments or maintenance with the machine unplugged from the power source.

14.Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

15.Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately after maintenance is complete.

16.Make sure the jointer is firmly secured to the stand or a bench before use.

17.Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

18.Provide for adequate space surrounding work area and non-glare, overhead lighting.

19.Keep the floor around the machine clean and free of scrap material, oil and grease.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Powermatic Part No. M-1791279DXWarranty and Service Warranty PeriodTable of Contents Page Page On-Off Switch Padlock On-Off Switch PadlockIntroduction Specifications Pre-wiredShipping Contents UnpackingUnpacking and Cleanup AssemblyInstalling Bed to Stand Installing Fence to Bed Installing the Drive BeltInstalling Cutterhead Guard Installing the Pulley CoverInstalling Access Door and Dust Chute Grounding Instructions ElectricalVolt Operation Adjustments Fence MovementFence Stop Adjustments 90º Stop AdjustmentInfeed Table Height Adjustment Initial Coarse AdjustmentRaise or lower the height adjustment handle Helpful Hint below Fine AdjustmentTable Gib Adjustment Outfeed Table Height AdjustmentSetting Cutterhead Knives Model 54A only Page Replacing Knives Model 54A only Setting Knives for Rabbeting and Nicks Model 54A only Determining Correct Table Height Operating Controls OperationControls Front View Controls Rear ViewHand Placement Basic OperationsDirection of Grain Never pass hands directly over the cutterheadSurfacing JointingBeveling Skewing Shear CuttingMaintenance LubricationPush Blocks Blade CareTo avoid injury from moving parts when moving this assembly Cutterhead RemovalTrouble Troubleshooting Operating ProblemsProbable Cause Remedy Optional Accessories Troubleshooting Mechanical and Electrical ProblemsReplacement Parts Stand Parts List All Models Index No. Part No Description Size QtyStand Assembly All Models Bed Parts List All Models 6285893 Fence Parts List and Assembly All Models Cutterhead Parts and Assembly model 54A only JJ6CSDX-101Cutterhead Parts and Assembly model 54HH only Wiring Diagrams Wiring Diagram Serial # 05060540312 and lowerWiring Diagram Serial # 05060540313 and higher Page New Sanford Road LaVergne, Tennessee Phone Modelos 54A y 54HH Parte No. M-1791279DXGarantía y Servicio Técnico Período de la GarantíaÍndice Page Page Candado para el Interruptor On-Off Candado para el Interruptor On-OffIntroducción Especificaciones Cableado paraDesempaque Contenido del Cont. de TransporteDesempaque y Limpieza MontajeInstalación de la Plataforma a la Base Instalación de la Guía a la Plataforma Instalación de la Correa de ImpulsiónInstalación de la Guarda de la Cabeza de Corte Instalación de la Cubierta de la PoleaInstalación de la Puerta de Acceso y el Colector de Polvo Instalación Eléctrica Instrucciones de Puesta a TierraOperación en 115 Voltios Operación a 230 VoltiosAjustes Movimiento de la GuíaAjustes de los Topes de la Guía Ajuste la tuerca de bloqueo JAjuste la Altura de la Mesa de entrada Limitador de Desplazamiento de la Mesa de entradaAjuste Inicial Grueso Ajuste FinoAjuste de la Doble Chaveta de la Mesa Ajuste de la Altura de la Mesa de SalidaAfloje ambos tornillos de bloqueo de la chaveta doble Figura Figura Sustitución de las Cuchillas Modelos 54A solamente Cabeza de CorteSustitución o Rotación de los Cuchillas Intercambiables Modelo 54HH solamenteDeterminación de Altura Correcta de la Mesa Controles de Operación OperaciónControles-Vista Frontal Controles Visión PosteriorOperaciones Básicas Colocación ManualDirección del Grano Nunca pase las manos directamente sobre el cabezal de corteCepillado EnsambladoBiselado Sesgado CizalladoMantenimiento LubricaciónBloques de Empuje Cuidado de las CuchillasRemoción de la Cabeza de Corte Retire la guarda de la hoja de corte a y el tornillo BProblema Diagnóstico de Problemas de OperaciónCausa Probable Solución Diagnóstico de Problemas Eléctricos y Mecánicos Refiérase a los Diagramas de Conexión paraAccesorios Opcionales Lista de PartesBase Lista de Partes Todos los Modelos Nro de Lista Parte Nro Descripción Tamaño CantidadBase Montaje Todos los Modelos Plataforma Lista de Partes Todos los Modelos 32-32 x 5/8 6296147 Guía Lista de Partes y Conjunto Todos los Modelos Cabeza de Corte Partes y Conjunto modelo 54A solamente Cabeza de Corte Partes y Conjunto modelo 54HH solamente Diagramas de Cableado Diagrama de Cableado Nro de Serie # 05060540312 y menoresDiagrama de Conexiones Nro de Serie # 05060540313 y mayores Page New Sanford Road LaVergne, Tennessee Dégauchisseuse de menuiserie six pouces Pièce N M-1791279DXGarantie et entretien Période de garantieTable des matières Page Page Cadenas du commutateur d’activation et de désactivation Verrou du commutateur d’activation et de DésactivationIntroduction Spécifications 115V pré-connectéDéballage Contenu à lexpéditionDéballage et nettoyage AssemblageMontage du lit sur le support Montage de la courroie dentraînement Montage du guide sur le litImmobilisez le manche de Montage de la protection de la tête de la découpeuse Montage du couvercle de la poulieMontage de la porte d’accès et de la chute de poussière Circuit électrique Instructions relatives à la mise à la masseFonctionnement sous 115 volts Fonctionnement sous 230 voltsDéplacement de la protection RéglagesRéglages d’arrêt du guide Et la cale d’arrêt CSerrez le manche de blocage a Serrez l’écrou de blocage JLimiteur de déplacement de la table d’entrée Réglage de la hauteur de la table d’entréeRéglage initial brut Réglage subtilRéglage du verrou de la porte Réglage de la hauteur de la table de sortiePage Page Remplacement des couteaux Modèle 54A uniquement Page Définition de la hauteur appropriée de la table Vue de face des commandes Vue arrière des commandesContrôles de fonctionnement FonctionnementOpérations de base Installation de la mainSens du grain Ponçage de surface AssemblageBiseautage Décalage découpe au ciseauGraissage Coupes de rainure tête de la découpeuse droite uniquementCales de poussée Entretien de la lameDépose de la tête de la découpeuse Dépannage des problèmes fonctionnels Cause possible SolutionAnomalies Dépannage des problèmes mécaniques et électriques Accessoires en optionPièces de rechange Support liste des pièces Tous les modèles ’indice N de la pièce Description Taille QtéSupport dispositif Tous les modèles Lit liste de pièces Tous les modèles Ressort Guide listes des pièces et dispositif Tous les modèles TS-1501021 Vis de bouchon de tête de la prise de courant 1791212 Coupe-paraison jeu de Total JWP208HH-111 Schémas de circuit électrique Page Page New Sanford Road LaVergne, Tennessee Téléphone
Related manuals
Manual 3 pages 10.4 Kb
Top Page Image Contents