Powermatic 209HH Outfeed Roller Height, Infeed Roller Height, Chipbreaker Height

Page 17

Outfeed Roller Height

1.Disconnect machine from power source.

2.Make sure the knives are set properly as previously explained under "Knife Adjustment."

3.Place the gauge block (J, Figure 26) on the table directly beneath the cutterhead (D, Figure 26).

4.Using a 0.02" (0.5mm) feeler gauge (K, Figure 26) placed on top of the gauge block, raise the work table until the knife just touches the feeler gauge when the knife is at its lowest point. Do not move the work table any further until the outfeed roller is adjusted.

5.Remove the feeler gauge and move the gauge block (J, Figure 27) under one end of the outfeed roller (F, Figure 27). The bottom of the outfeed roller should just touch the top of the gauge block. If an adjustment to the outfeed roller is necessary, loosen the lock nut (L, Figure 27) and turn screw (M, Figure

27)until the outfeed roller just touches the gauge block. Then tighten lock nut (L, Figure

6.Check and adjust the opposite end of the outfeed roller in the same manner.

Infeed Roller Height

Use the exact same procedure for checking the infeed roller as you did for the outfeed roller, except use a .004" (0.1mm) feeler gauge atop the gauge block. If adjustment is necessary, use the lock nut and screw on each end of the infeed roller.

Chipbreaker Height

The chipbreaker breaks off the larger chips before the stock reaches the cutterhead. Use the gauge block and a .004" (0.1mm) feeler gauge to check the height of the chipbreaker, following the same procedure as above. If adjustment is needed:

1.Remove top cover.

2.Loosen the lock nuts (A, Figure 28) at both ends of the chipbreaker, and turn the set screws to raise or lower the chipbreaker as needed. The set screws should be turned the same amount.

3.When the chipbreaker contacts the gauge block, tighten both lock nuts (A, Figure 28).

Figure 26

Figure 27

Figure 28

17

Image 17
Contents Revision D1 11/06 Copyright WMH Tool Group Vantage Drive Elgin, IllinoisMore Information Warranty and ServiceTable of Contents Page Page Introduction Features Specifications Unpacking Crate Contents FigureHandwheel AssemblyKnife Gauge model 209 only Electrical Connections Extension TablesDust Hood Extension Cords AdjustmentsBelt Tension Table RollersCutterhead Knife Adjustments Model 209 onlyReplacing and Re-setting Knives Model 209 only Repeated Replacing or Rotating Knife Inserts Model 209HH onlyKnow the Transmitting Rollers of Your Planer Figure Work Table Parallel to CutterheadInfeed and Outfeed Roller Spring Tension Anti-Kickback FingersChipbreaker Height Outfeed Roller HeightInfeed Roller Height Pressure Bar Height Changing Accessories for Lowest Feed SpeedChip Deflector Feed Speed ControlDepth of Cut Return RollersLubrication MaintenanceFigure No Trouble Troubleshooting Operating ProblemsTroubleshooting Mechanical and Electrical Problems Replacement Parts Optional AccessoriesCutterhead Assembly 209HH-1003 Parts List Cutterhead AssemblyTS-1482011 TS-1524031209-1094 209-1097 Strain Relief, Momentary Switch Cord TS-1540031209-1095 209-1096Base Assembly Parts List Base Assembly Gearbox Assembly TS-1503041 Parts List Gearbox AssemblyTS-1482031 209HH-415Stand Assembly Parts List Stand Assembly TS-1523041 Parts List Table Assembly209-2011 209-2012 TS-1490041Electrical Connections Single Phase, 230 Volt only Electrical Connections 3 Phase, 230 Volt only Electrical Connections 3 Phase, 460 Volt only Work area around machine marked off clearly Gum and pitch with oven cleanerEraser Check leveling of extension tables with main tablePage WMH Tool Group Vantage Drive Elgin, IL Phone
Related manuals
Manual 120 pages 26.72 Kb

209HH, 209 specifications

The Powermatic 209 and the Powermatic 209HH are two premium models in the range of high-performance drill presses designed for serious woodworkers and metalworkers alike. These machines are lauded for their combination of durability, precision, and innovative features, making them favorable choices in workshops that demand reliable and efficient performance.

One of the standout features of the Powermatic 209 is its robust construction. The machine boasts a heavy-duty cast iron base and column, ensuring stability during operation and reducing vibrations that could affect drilling accuracy. This solid foundation is complemented by a precisely machined table, which can be adjusted for height and angle, allowing for increased flexibility for various drilling applications.

The Powermatic 209 uses a powerful motor that provides ample torque for a variety of materials, from soft woods to tougher metals. The variable speed control feature allows users to easily adjust the spindle speed to match the requirements of the specific operation, accommodating drill bits of different sizes and materials. This adaptability is further enhanced in the 209HH model, which is equipped with an integrated digital RPM readout. This technology provides real-time feedback to the operator, allowing for optimal speed adjustments and ensuring enhanced accuracy.

Another key characteristic of the Powermatic 209 and 209HH is their precision-engineering features. The machines include a laser positioning system, which aids in aligning drill bits with great accuracy on the workpiece. This feature significantly reduces setup time and ensures consistent results, especially on intricate drilling tasks.

Furthermore, both models come with a quick-release table, making it easy to switch between various workpieces. The adjustable quill depth stop is another notable feature, allowing operators to set precise depths for repeated drilling tasks, thus enhancing productivity.

In conclusion, the Powermatic 209 and 209HH drill presses stand out in the marketplace for their combination of robust construction, advanced technology, and precision engineering. These machines not only ensure high-quality results but also bring a level of efficiency and adaptability that is vital for serious craftsmen. Whether in a professional shop or a dedicated home workshop, the Powermatic 209 and 209HH are built to perform and built to last.