RIDGID R4330 manual Operation, Applications, Thickness planing, Planing tips

Page 17

OPERATION

WARNING:

Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury.

WARNING:

Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thrown into your eyes resulting in possible seri- ous injury.

WARNING:

Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury.

WARNING:

The use of this planer on materials not listed may damage the planer and may cause serious personal injury.

WARNING:

Never plane workpiece with loose knots or foreign objects. Do not plane workpieces that are severely bowed, twisted, or knotted. Cutter blades can dull, chip, or break causing possible serious personal injury.

WARNING:

Do not force feed the workpiece through the machine. Let the planer apply the proper feed rate.

APPLICATIONS

You may use this tool for the purpose listed below:

Planing the surface of a piece of lumber.

thickness planing

Thickness planing sizes workpiece to desired thickness while creating a smooth, level surface. Thickness of each cut will depend on type of wood (hardwood versus softwood), width of workpiece, straightness, dryness, and grain composition. Whenever working with a new type of wood, make thin test cuts on a scrap piece of wood first to determine potential problems with the workpiece.

PLANING tips

Thickness planers work best if at least one side of the workpiece has a flat surface. When both sides of a workpiece are rough, use a surface planer or jointer first to define the initial flat surface. Plane one side of the workpiece then flip the workpiece and plane the surface of the reverse side.

Always plane both sides of a workpiece to reach the desired thickness. This will leave the workpiece with uniform moisture to prevent warp during the drying process.

When one end of the workpiece is thicker than the opposite end by more than 1/8 in., make several cuts with the planer starting with light planing cuts first. Remember, light cuts create a finer finish than heavier cuts.

Do not plane a workpiece less than 5/16 in. thick.

Do not plane a workpiece less than 3/4 in. wide.

Do not plane workpiece shorter than 14 in. long as this will cause kickback.

Do not plane more than one workpiece at a time.

Do not lower the cutterhead assembly lower than 5/16 in.

Do not continuously use the planer set at the maximum depth of cut (1/8 in.) and at full width of cut (13 in.). Continuous use at maximum cutting capacity will damage the motor.

Worn cutter blades will affect cutting accuracy. Planing with dull or nicked cutter blades may produce ridges or rough workpiece surfaces.

Gum and pitch on the cutter blades will cause them to wear prematurely. Using a gum and pitch remover to keep your cutter blades clean will prolong their wear.

Refer to the Maintenance section of this operator’s manual for instructions on how to remove and replace or turn the cutter blades.

Note: Cutter blades are double-edged and can be turned once to the opposite, unused edge before replacement is required. Cutter blades must ALWAYS be replaced as a set.

17

Image 17
Contents OPERATOR’S Manual Introduction Table of contentsRead ALL Instructions General Safety Rules Never Start a Tool When ANY ROTATiNG Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsAuthorized Service Center for repair. When servic ServiceElectrical Speed and WiringExtension Cords Grounding InstructionsMotor Overload Protector Motor safety protectionArbor Anti-Kickback Pawls radial arm and table sawsBevel Cut ChamferProduct Specifications FeaturesAutomatic Feed AMP MotorBlade / Tool Storage Dust HoodDust Hood knobs Loose PartsHood Hex key Magnetic Blade tool Unpacking AssemblyMounting the Planer to workbench Clamping Planer to WorkbenchInstalling the Dust Hood Installing handwheel knobLock NUT Leveling the Table ExtensionsApplications OperationThickness planing Planing tipsAvoiding Snipe Power SwitchWarped Wood To lock the PlanerDepth Gauge Adjusting the planing depth See FigureCutterhead Replaning using repeat-a-cutIndicator Thickness Scale Adjustment AdjustmentsBlade Adjustment ScrewsReplace the handwheel and hex head screw Replace the replane indicatorRepeat-a-cut Lubrication MaintenanceCleaning Brush Cap Brush ReplacementCord storage Blade Blade ReplacementDrive Belt Hex key Loo sen Tighten Troubleshooting DAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredModel No R4330 Serial No Customer Service Information