Delta TP400LS instruction manual Additional Safety Rules for Planers

Page 4

ADDITIONAL SAFETY RULES FOR PLANERS

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.

1.DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury.

2.OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not thoroughly familiar with the operation of this machine. Knowledge is safety.

3.FOLLOW ALL WIRING CODES and recommend- ed electrical connections to prevent shock or electrocution.

4.KEEP KNIVES SHARP and free from rust and pitch. Dull or rusted knives work harder and can cause kickback.

5.NEVER TURN THE MACHINE “ON” before clearing the table of all objects (tools, scraps of wood, etc.). Flying debris can cause serious injury.

6. NEVER TURN THE MACHINE “ON” with the work- piece contacting the cutterhead. Kickback can occur.

7.SECURE THE MACHINE TO A SUPPORTING SUR- FACE to prevent the machine from sliding, walking or tipping over.

8.PROPERLY SECURE THE KNIVES IN THE CUTTER- HEAD before turning the power “ON”. Loose blades may be thrown out at high speeds causing serious injury.

9.LOCK THE SPEED SETTING SECURELY before feeding the workpiece through the machine. Changing speeds while planing can cause kick- back.

10.AVOID AWKWARD OPERATIONS AND HAND POSI- TIONS. A sudden slip could cause a hand to move into the knives.

11.KEEP ARMS, HANDS, AND FINGERS away from the cutterhead, the chip exhaust opening, and the feed rollers to prevent severe cuts.

12.NEVER REACH INTO THE CUTTERHEAD AREA while the machine is running. Your hands can be drawn into the knives.

13.DO NOT STAND IN LINE OF THE WORKPIECE. Kickback can cause injury.

14.ALLOW THE CUTTERHEAD TO REACH FULL SPEED before feeding a workpiece. Changing speeds while planing can cause kickback.

15.WHEN PLANING BOWED STOCK, place the concave (cup down) side of the stock on the table and cut with the grain to prevent kickback.

16.DO NOT FEED A WORKPIECE that is warped, contains knots, or is embedded with foreign objects (nails, staples, etc.). Kickback can occur.

17.DO NOT FEED A SHORT, THIN, OR NARROW WORKPIECE INTO THE MACHINE. Your hands can be drawn into the knives and/or the workpiece can be thrown at high speeds. See the “OPERATION” section of this instruction manual for details.

18.DO NOT FEED A WORKPIECE into the outfeed end of the machine. The workpiece will be thrown out of the opposite side at high speeds.

19.REMOVE SHAVINGS ONLY with the power “OFF” to prevent serious injury.

20.PROPERLY SUPPORT LONG OR WIDE WORK- PIECES. Loss of control of the workpiece can cause serious injury.

21.NEVER PERFORM LAYOUT, ASSEMBLY or set-up work on the table/work area when the machine is running. Serious injury will result.

22.TURN THE MACHINE “OFF”, DISCONNECT IT FROM THE POWER SOURCE, and clean the table/work area before leaving the machine. LOCK THE SWITCH IN THE “OFF” POSITION to prevent un- authorized use. Someone else might accidentally start the machine and cause injury to themselves or others.

23.ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others.

4

Image 4
Contents 12½ Portable Planer General Safety Rules Safety Guidelines DefinitionsImportant Safety Instructions Failure to Follow These Rules MAY Result in Serious Injury Stay ALERT, Watch What YOU are DOING,Additional Safety Rules for Planers Failure to Follow These Rules MAY Result in Serious InjuryMotor Specifications Power ConnectionsGrounding Instructions Extension Cords Minimum Gauge Extension CordUnpacking and Cleaning Functional DescriptionPlaner Parts AssemblyStand Lowering Extension Tables Cutterhead Lock HandleCutterhead Raising and Lowering Handle Leveling Table ExtensionsFastening Planer to Stand Operating Controls and Adjustments Locking Switch OFF PositionRaising and Lowering Head Assembly Starting Stopping PlanerRecommended Depth of CUT Disconnect Machine from Power SourceLeveling Table Extensions Knife Transfer Tool Storage Wrench StorageReplacing Knives Carrying HANDLE/STOCK Transfer BARKnives are Sharp Page Adjusting Height of Outfeed Roller Operation Brush Inspection Replacement MaintenanceLubrication Page Accessories Canadian PORTER-CABLE Delta Service Centers