Miller Electric M-15 manual Principal Safety Standards

Page 7

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring – be sure power supply system is properly sized, rated, and protected to handle this unit.

MOVING PARTS can cause injury.

DKeep away from moving parts such as fans.

DKeep all doors, panels, covers, and guards closed and securely in place.

FALLING UNIT can cause injury.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling boards or parts.

DUse proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can cause injury.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can cause injury.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

1-4. Principal Safety Standards

Safety in Welding and Cutting, ANSI Standard Z49.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126

Safety and Health Standards, OSHA 29 CFR 1910, from Superinten- dent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.

Recommended Safe Practices for the Preparation for Welding and Cut- ting of Containers That Have Held Hazardous Substances, American Welding Society Standard AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126

National Electrical Code, NFPA Standard 70, from National Fire Protec- tion Association, Batterymarch Park, Quincy, MA 02269.

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, from Compressed Gas Association, 1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202.

Code for Safety in Welding and Cutting, CSA Standard W117.2, from Canadian Standards Association, Standards Sales, 178 Rexdale Boulevard, Rexdale, Ontario, Canada M9W 1R3.

Safe Practices For Occupation And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute, 1430 Broadway, New York, NY 10018.

Cutting And Welding Processes, NFPA Standard 51B, from National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

OM-1314 Page 3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Processes OM-1314Description From Miller to You Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesPrincipal Safety Standards About Pacemakers EMF InformationLES Fumé ES ET LES GAZ peuvent ê tre dangereux Signification des symbolesConsignes DE Securite Lire Avant Utilisation UN Choc É Lectrique peut tuerDES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer un incendie ou une explosionLE Bruit peut affecter l’ouïe DES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OULA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peutInformation sur les champs é lectromagné tiques Principales normes de sé curitéConsignes relatives aux stimulateurs cardiaques Specifications InstallationVolt-Ampere Curves Overheating Duty Cycle And OverheatingInstalling Gas Supply Installing Work ClampFollow wire manufacturer’s recommendation Selecting a Location And Connecting Input Power Electrical Service GuideDo not move or operate unit Where it could tip Standard Wire Spool Standard Wire Reel Installing Wire Spool And Adjusting Hub TensionInstalling Drive Roll And Threading Welding Wire 14 ga 16 ga 18 ga 20 ga 22 ga OperationWeld Parameters ControlsFuse F1 Maintenance & TroubleshootingMaintenance MonthsReplacing Gun Contact Tip Turn Off power before replacing contact tipUnicable Repair Disconnect gun from unit Cleaning Or Replacing Gun LinerTo Reassemble Gun Remove handle Remove switch housing. Note If installing new Replacing Switch And/Or Head TubeTurn Off power before cleaning or repairing drive assembly Cleaning Or Repairing Drive AssemblyWelding Trouble Remedy TroubleshootingCircuit Diagram Electrical DiagramTypical MIG Process Connections MIG Welding Gmaw GuidelinesSelect Voltage Typical MIG Process Control SettingsWire Recommendation Wire Speed Select Wire SizeHolding And Positioning Welding Gun Conditions That Affect Weld Bead Shape Good Weld Bead Characteristics Poor Weld Bead CharacteristicsGun Movement During Welding Possible Causes Corrective Actions Troubleshooting Excessive SpatterTroubleshooting Porosity Troubleshooting Excessive PenetrationTroubleshooting Incomplete Fusion Troubleshooting Lack Of PenetrationTroubleshooting Burn-Through Troubleshooting Distortion Troubleshooting Waviness Of BeadApplication Common MIG Shielding GasesFlat & Horizontal1 Fillet OM-1314 Main Assembly Parts ListDia Part Mkgs Description Quantity M-15 Gun M-15 Gun -1 Item 169Drive Assembly, Wire -1 Item Support ServiceMiller Electric Mfg. Co Owner’s Record

M-15 specifications

Miller Electric M-15 is a highly regarded welding machine designed to cater to a variety of welding applications in both industrial and commercial environments. Known for its reliability and efficiency, the M-15 stands out in the Miller Electric lineup due to its impressive performance and user-friendly features.

One of the primary characteristics of the M-15 is its versatility. It supports multiple welding processes, including MIG, TIG, and Stick welding. This multi-process capability allows operators to switch between different techniques without needing to change equipment, making it an ideal choice for fabricators and maintenance professionals who handle various welding tasks.

The M-15 is engineered with advanced inverter technology, which enhances its performance and efficiency. This technology allows for a lightweight design while still delivering powerful output. The machine offers a wide range of amperage, making it suitable for welding thin materials as well as thicker sections. As a result, the M-15 can tackle everything from delicate sheet metal projects to robust structural welds.

Another standout feature is its intuitive control panel, which simplifies operation for both novice and experienced welders. The easy-to-read display provides essential information regarding settings and performance, allowing users to make adjustments on the fly. This user-friendly interface minimizes the learning curve and maximizes productivity in the workshop.

In terms of safety, the Miller Electric M-15 incorporates several features designed to protect users during operation. Its built-in thermal overload protection automatically shuts down the machine in case of overheating, thus preventing damage to the equipment and ensuring the safety of the operator.

Durability is also a hallmark of the M-15. Constructed with high-quality materials, this welding machine is built to withstand the rigors of daily use in demanding environments. The housing is designed to protect internal components from dust, debris, and accidental impacts, ensuring consistent performance over time.

Overall, the Miller Electric M-15 combines advanced technology, versatility, and reliability into a compact and powerful welding machine. Its user-friendly design, safety features, and robust construction make it a top choice for professionals looking to invest in a reliable welding solution. Whether for heavy industrial applications or lighter fabrication work, the M-15 is equipped to meet a wide range of welding challenges with confidence.
Top Page Image Contents