Miller Electric OM-220 390F manual Feeder Set Up Push Button, Adjust Knob

Page 26

6-7. Feeder Set Up Push Button

3

4

2

FeederSetup

 

Start

Crater

 

Time

Time

1

Preflow

Postflow

Time

 

 

 

Time

 

 

 

 

 

 

 

 

 

 

Sequence Diagram

1Feeder Set Up Push Button LED

2Feeder Set Up Push Button

Press button to choose Sequence. Feeder Set Up push-button LED will illuminate.

3 Sequence LED

When the Feeder Set Up button is pressed once, the Sequence LED will illuminate and the upper display will show sequence options. Use the Adjust knob to select PRE (preflow), STRT (start), CRTR (crater), or POST (postflow).

Press the lower display push button and the Lower Display push-button LED will illuminate as well as the lower display. The Time LED will automatically begin flashing indicating that a time value can be entered by turning the Adjust knob. By entering a time value the sequence state will become active. To turn off a sequence state, change the time value to OFF. To step back for selecting another sequence option, press

the Upper Display push button.

The Sequence option STRT and CRTR will have additional parameter settings. By pushing the Lower Display push button a second time, while STRT or CRTR appear in the upper display, allows entering voltage (MIG) or Arc Adjust [Pulse, Accu-pulse, or RMD (optional)]. Use the Adjust knob to change the values indicated by the flashing LED for either Volts or Arc Adjust. Pressing the Lower Display push button a third time will activate the WFS setting for either STRT or CRTR and the WFS LED will begin flashing. Use the Adjust knob to change the WFS value.

Pressing the Feeder Set Up button two more times will exit the Sequence menu and return the system to standby mode.

4 Trigger Control LED

Press the Feeder Set Up button twice and the Trigger Control LED will illuminate, and the upper display will show the different

trigger control selections. Use the Adjust knob to cycle through the trigger control methods as follows: DS, TH, TDS, TPS, and 4T (see Section 6-1for definitions). The lower display will show the current state of each trigger control method as being on or off. Not all trigger control methods are compatible with each other, therefore, turning on certain trigger selections will cause other trigger selections to turn off.

Press the lower display push button to illuminate the push-button LED and enable the use of the Adjust knob to allow turning selected trigger control methods on or off. If trigger hold is set to on, the Trigger Hold LED will illuminate.

.Trigger Hold is automatically set to On

with the 4T trigger selection. This is part of the 4T function.

Press the Feeder Set Up button a third time to cycle back to standby mode.

6-8. Adjust Knob

1 Adjust Knob

The Adjust knob is used to change functions and parameters. Refer to the front panel sections for information regarding use of this control.

1

Adjust

OM-220 390 Page 22

Image 26
Contents Description OM-220 390FProcesses File Advanced Manufacturing SystemsFrom Miller to You Table of Contents Standards Decwire2/04Directives Arc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer unIncendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures graves’EMPLOI Excessif peut SUR Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaquesKeep your head out of the fumes Disconnect input plug or power before working on machine− Definitions Symbols And Definitions Manufacturer’s Rating Label For CE Products− Introduction − InstallationSpecifications Selecting a LocationConnection Diagram Rear Panel Connections And Rotating Drive Assembly Pin Network Receptacle Information Gun Recommendation TableInstalling And Threading Welding Wire Power Source Upper Display Lower Display Voltage Range Feeder Display At Power UpDual Schedule Switch Option Net Wait− Operation Operational TermsPower Switch See Section Front Panel SectionsSee Program Push Button Upper DisplayLower Display Amps LEDFeeder Set Up Push Button Adjust KnobProcess Set Up Push Button ProcessSetupJog/Purge Jog/Purge Push Button Adjust Knob Gun Trigger ReceptacleJog/Purge switch provides the following functions Mild Steel Reset ModePulse Accu-pulseSequence Parameters − Setting Sequence ParametersSequence Parameters In a Program − Maintenance Routine MaintenanceDiagnostics Closed error Indicates a triggerTrouble Remedy TroubleshootingDisconnect power before troubleshooting OM-220 390 − Electrical Diagram Circuit Diagram211 005-E − Parts List − Fig 21 − Fig 10-2Part Description Quantity Control Box PLG4 Drive Assembly, Wire Drive Assembly, Wire -1Item1.4 mm Metric1.2 mm Page Page Page Support ServiceYour distributor also gives For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s