Miller Electric OM-220 390F Definitions, Disconnect input plug or power before working on machine

Page 13

SECTION 3 − DEFINITIONS

3-1. Warning Label Definitions

1

1.1

 

1.2

1.3

2

2.1

2.2

 

2.3

3

3.1

 

3.2

3.3

4

4.1

+

+

+

 

 

5

+

 

 

6

 

 

 

 

 

 

 

 

S-178 936

Warning! Watch Out! There are possible hazards as shown by the symbols.

Drive rolls can injure fingers

Welding wire and drive parts are at welding voltage during operation − keep hands and metal objects clear.

1 Electric shock can kill.

1.1Wear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves.

1.2Protect yourself from electric shock by insulating yourself from work and ground.

1.3Disconnect input plug or power before working on machine.

2Breathing welding fumes can be hazardous to your health.

2.1Keep your head out of the fumes.

2.2Use forced ventilation or local exhaust to remove the fumes.

2.3Use ventilating fan to remove fumes.

3Welding sparks can cause explosion or fire.

3.1Keep flammables away from welding. Don’t weld near flammables.

3.2Welding sparks can cause fires. Have a fire extinguisher nearby and have a watch person ready to use it.

3.3Do not weld on drums or any closed containers.

4Arc rays can burn eyes and injure skin.

4.1Wear hat and safety glasses. Use ear protection and button shirt collar. Use welding helmet with correct shade of filter. Wear complete body protection.

5Become trained and read the instructions before working on the machine or welding.

6Do not remove or paint over (cover) the label.

OM-220 390 Page 9

Image 13
Contents Processes OM-220 390FDescription File Advanced Manufacturing SystemsFrom Miller to You Table of Contents Directives Decwire2/04Standards Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier Incendie ou une explosion LE Soudage peut provoquer unDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques Principales normes de sécurité− Definitions Disconnect input plug or power before working on machineKeep your head out of the fumes Manufacturer’s Rating Label For CE Products Symbols And DefinitionsSpecifications − Installation− Introduction Selecting a LocationConnection Diagram Rear Panel Connections And Rotating Drive Assembly Gun Recommendation Table Pin Network Receptacle InformationInstalling And Threading Welding Wire Dual Schedule Switch Option Feeder Display At Power UpPower Source Upper Display Lower Display Voltage Range Net WaitOperational Terms − OperationPower Switch See Front Panel SectionsSee Section Upper Display Program Push ButtonAmps LED Lower DisplayAdjust Knob Feeder Set Up Push ButtonProcessSetup Process Set Up Push ButtonJog/Purge switch provides the following functions Jog/Purge Push Button Adjust Knob Gun Trigger ReceptacleJog/Purge Pulse Reset ModeMild Steel Accu-pulseSequence Parameters In a Program − Setting Sequence ParametersSequence Parameters Routine Maintenance − MaintenanceDiagnostics Indicates a trigger Closed errorDisconnect power before troubleshooting TroubleshootingTrouble Remedy OM-220 390 Circuit Diagram − Electrical Diagram211 005-E − Fig 21 − Fig 10-2 − Parts ListPart Description Quantity Control Box PLG4 Drive Assembly, Wire -1Item Drive Assembly, Wire1.2 mm Metric1.4 mm Page Page Page Your distributor also gives ServiceSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s