Miller Electric 293 Installing Drive Rolls and Wire Guide, Aligning Drive Rolls and Wire Guide

Page 17

3-9. Installing Drive Rolls and Wire Guide

		1	Securing Screw
		2	Inlet Wire Guide
		Loosen screw. Slide tip as close to
		drive rolls as possible without
		touching. Tighten screw.
	5	3	Anti-Wear Guide
	3	Install guide as shown.
	3	4	Drive Roll
		4	Drive Roll
	2	The drive roll consists of two differ-
		ent sized grooves. The stamped
		markings on the end surface of the
		drive roll refers to the groove on the
		opposite side of the drive roll. The
		groove closest to the motor shaft is
		the proper groove to thread.
		5	Drive Roll Securing Nut.
	1	Turn nut one click to secure drive
	1	roll.
	4

Tools Needed:

5/64 in 7/16 in

3-10. Aligning Drive Rolls and Wire Guide

			Y Turn Off power.
			View is from top of drive rolls
			looking down with pressure
			assembly open.
	Correct	Incorrect	1	Drive Roll Securing Nut
	Correct	Incorrect
3	4		2	Drive Roll
2			3	Wire Guide
2
1			4	Welding Wire
			5	Drive Gear
	5		Insert screwdriver, and turn screw
			in or out until drive roll groove lines
			up with wire guide.
			Close pressure roll assembly.

Tools Needed:

Ref. 800 412-A

OM-223 194 Page 13

Image 17

Contents Description OM-223 194E 2006−09Processes From Miller to You Table of Contents DecstatMilan6/05 DirectivesStandards Arc Welding Hazards Symbol UsageElectric Shock can kill Fumes and Gases can be hazardousWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsElectric shock can kill − DefinitionsFalling unit can cause injury Where it could tipDo not move or operate unit Cylinders can expolde ifWear approved safety Electrical shock from wiringCan kill Working on this machineSpecifications − InstallationModel Duty Cycle And OverheatingVolt-Ampere Curves Installing Wire Spool and Adjusting Hub Tension Installing Gas SupplyElectrical Service Guide Positoning Jumper Links 230/400V 3-Phase Models271 273 293 333 383 230 400L2 L3 Aligning Drive Rolls and Wire Guide Installing Drive Rolls and Wire GuideThreading Welding Wire and Adjusting Pressure Roll Tension Setting Gun Polarity for Wire Type Optional Using Gun/Cable HolderControls for Migmatic 293/333 − OperationControls for Migmatic 271/273 Spot Weld Timer Run-In, Burnback Optional and Spot Weld Timer ControlsControls for Migmatic Run-In ControlRoutine Maintenance − Maintenance &TROUBLESHOOTINGCircuit Breaker CB1 Unit OverloadCheck voltage switchs. Replace if necessary TroubleshootingReplace Z1 if necessary Nections. Check secondary voltages. Replace T1 if necessaryOM-223 194 Circuit Diagram for Migmatic − Electrical DiagramsCircuit Diagram for Migmatic 273 400 VAC Circuit Diagram for Migmatic 293 400 VAC Circuit Diagram for Migmatic 333 400 VAC Circuit Diagram for Migmatic 383 400 VAC Wrapper Assembly, All Models − Parts ListPart Description Quantity Main Assembly for Migmatic Dia Part Description Quantity Mkgs Main Assembly for Migmatic Dia Part Description Main Assembly for Migmatic PL2 Main Assembly for Migmatic PL1 Main Assembly for Migmatic TP1 Wire Drive and Gears 2 roll See Table Drive Roll & Wire Guide KitsWire Drive and Gears 4 roll Drive Roll And Wire Guide Kits 4 Roll Models Drive Roll And Wire Guide Kits 2 Roll Models1.0 mm 1.2 mmPage Page Effective January 1 Transportation Department For assistance in filing or settling claims, contactYour distributor and/or equipment manufacturer’s