Miller Electric Axcess 300 manual Electrical Service Guide, Three

Page 26

4-10. Electrical Service Guide

Failure to follow these electrical service guide recommendations could create an electric shock or fire hazard. These recommenda- tions are for a dedicated branch circuit sized for the rated output and duty cycle of the welding power source.

NOTICE − INCORRECT INPUT POWER can damage this welding power source. This welding power source requires a CONTINUOUS supply of input power at rated frequency(+10%) and voltage (+10%). Phase to ground voltage shall not exceed +10% of rated input voltage. Do not use a genera- tor with automatic idle device (that idles engine when no load is sensed) to supply input power to this welding power source.

.Actual input voltage should not exceed ± 10% of indicated required input voltage. If actual input voltage is outside of this range, output may not be available.

 

Three

 

Phase

 

50/60 Hz

 

 

Input Voltage

400

 

 

Input Amperes At Rated Output

10.4

 

 

Max Recommended Standard Fuse Rating In Amperes

 

Circuit Breaker 1, Time-Delay 2

10

Normal Operating 3

15

 

 

Min Input Conductor Size In AWG 4

14

Max Recommended Input Conductor Length In Feet (Meters)

223

(68)

 

 

 

Min Grounding Conductor Size In AWG 4

14

Reference: 2005 National Electrical Code (NEC) (including article 630)

1Choose a circuit breaker with time-current curves comparable to a Time Delay Fuse.

2“Time-Delay” fuses are UL class “RK5” .

3“Normal Operating” (general purpose - no intentional delay) fuses are UL class “K5” (up to and including 60 amp), and UL class “H” ( 65 amp and above).

4Conductor data in this section specifies conductor size (excluding flexible cord or cable) between the panelboard and the equipment per NEC Table 310.16. If a flexible cord or cable is used, minimum conductor size may increase. See NEC Table 400.5(A) for flexible cord and cable requirements.

OM-230 032 Page 20

Image 26
Contents Description OM-230 032CProcesses File Advanced Manufacturing SystemsFrom Miller to You Table of Contents − Troubleshooting Decstat1/07 DirectivesStandards Page Electric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can cause severe burnsWelding can cause fire or explosion Fumes and Gases can be hazardousARC Rays can burn eyes and skin Flying Metal or Dirt can injure eyesFalling Unit can cause injury Welding Wire can cause injuryFire or Explosion hazard Moving Parts can cause injuryEMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux Risque D’INCENDIE OU D’EXPLO LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées LA Chute DE L’APPAREIL peut blesserLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-230 032 Manufacturer’s Warning Label Definitions Disconnect input plug or power before working on machine− Definitions Keep your head out of the fumesWeee Label I1eff Symbols And DefinitionsI1max Manufacturer’s Rating LabelDimensions And Weight − InstallationSpecifications 100% Duty Cycle At 225 Amperes Duty Cycle And OverheatingVolt-Ampere Curves OverheatingMovement Tipping Do not move or operate Connection DiagramSelecting a Location LocationReceptacle supplies Rear Panel Receptacles And Supplementary Protectors115 V 10 a AC Receptacle RC2 From RC2 is limited by supplementaryConnecting To Weld Terminals Network Wire Feeder Receptacle Functions PinInput Voltage 400 Input Amperes At Rated Output Electrical Service GuideThree Disconnect Device Input Power Connections Connecting Input PowerWelding Power Source Input Power Connections − Recommended Setup Procedures Selecting Weld Cable SizesWelding Circuit Gun TravelWCL Current Flow PathBest BadBetter Using Multiple Welding Power Sources Bad Setup Wire Feeder Drop in the workpiece. The voltage dropBetter Setup Supporting separate voltage feedback to OM-230 032Best Setup Options Front Panel Switches− Operation Blowing Out Inside Of Unit − MaintenanceRoutine Maintenance Servicing Hazards − Safety Precautions for ServicingShock Hazard from testing Exploding Parts can cause injuryCalifornia Proposition 65 Warnings − Troubleshooting Removing Cover and Measuring Input Capacitor VoltageStatus Diagnosis Weld Process Board PC4 Diagnostic LED’sDiagnostic LED’s On Process Board PC4 Red Network And Module Status LED’s Network Status LED’sModule Status LED’s Circuit board is operating normallyTroubleshooting Trouble RemedyOM-230 032 − Electrical Diagrams Circuit Diagram For Welding Power Source229 810-A 17 − Fig 1411 − Parts List− Fig HD2 Windtunnel Assembly LH And RH Windtunnel Assembly LH And RH 1Item Top Tray Assembly Rear Panel Assembly Front Panel Assembly Dia Part Page Support ServiceYour distributor also gives For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s

Axcess 300 specifications

The Miller Electric Axcess 300 is a cutting-edge power source designed for advanced welding applications. This machine stands out in the marketplace for its unique combination of features, performance, and versatility. Ideal for industrial environments, the Axcess 300 is particularly well-suited for multi-process welding, allowing users to engage in MIG, TIG, and Stick welding with ease.

One of the hallmark features of the Axcess 300 is its exceptional output capability. With a maximum output of 300 amps, this machine is equipped to handle a variety of welding tasks ranging from light to heavy fabrication. The machine can easily accommodate materials of varying thicknesses, making it an exceptional choice for diverse welding projects.

Incorporating Miller's advanced Auto-Set technology, the Axcess 300 simplifies the setup process for welders. With just a few inputs from the operator, the machine intelligently adjusts itself to provide optimal welding conditions, ensuring high-quality results without the need for extensive expertise. This feature is especially beneficial for less experienced welders, allowing them to produce excellent welds with minimal guidance.

The Axcess 300 employs Miller's innovative X-Mode technology, which helps to maintain a stable arc even when working with challenging materials or in fluctuating conditions. This enhances arc control, minimizing defects such as spatter and burn-through. Moreover, the machine's extensive voltage range allows for superior performance over different welding procedures, contributing to more efficient operation overall.

Enhanced portability is another important characteristic of the Axcess 300. Its compact design and lightweight construction make it easy to transport, allowing operators to quickly move the machine to different job sites. The durable enclosure protects against the rigors of industrial use, ensuring a long operational lifespan.

Safety features integrated into the Axcess 300 include a built-in thermal overload protection system, which prevents the machine from overheating during heavy usage. Furthermore, the intuitive interface with easy-to-read displays allows for straightforward operational controls, enabling welders to focus on their work without unnecessary distraction.

In summary, the Miller Electric Axcess 300 is a versatile, powerful, and user-friendly welding power source that combines advanced technology with practical features, making it an invaluable asset for professionals in various sectors.