Miller Electric Axcess 300 manual Fire or Explosion hazard, Falling Unit can cause injury

Page 9

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.

FALLING UNIT can cause injury.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

MOVING PARTS can cause injury.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards closed and securely in place.

DHave only qualified persons remove doors, panels, covers, or guards for maintenance as necessary.

DReinstall doors, panels, covers, or guards when maintenance is finished and before reconnecting input power.

READ INSTRUCTIONS.

D Read Owner’s Manual before using or servic- ing unit.

DUse only genuine replacement parts from the manufacturer.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

FLYING SPARKS can cause injury.

D Wear a face shield to protect eyes and face.

D Shape tungsten electrode only on grinder with proper guards in a safe location wearing proper face, hand, and body protection.

DSparks can cause fires — keep flammables away.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can cause injury.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can cause injury.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

OM-230 032 Page 3

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Processes OM-230 032CDescription File Advanced Manufacturing SystemsFrom Miller to You Table of Contents − Troubleshooting Directives StandardsDecstat1/07 Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésDES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesserProposition californienne 65 Avertissements LES Fils DE Soudage peuvent provoquer des blessuresLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux OM-230 032 − Definitions Disconnect input plug or power before working on machineManufacturer’s Warning Label Definitions Keep your head out of the fumesWeee Label I1max Symbols And DefinitionsI1eff Manufacturer’s Rating Label− Installation SpecificationsDimensions And Weight Volt-Ampere Curves Duty Cycle And Overheating100% Duty Cycle At 225 Amperes OverheatingSelecting a Location Connection DiagramMovement Tipping Do not move or operate Location115 V 10 a AC Receptacle RC2 Rear Panel Receptacles And Supplementary ProtectorsReceptacle supplies From RC2 is limited by supplementaryConnecting To Weld Terminals Pin Network Wire Feeder Receptacle FunctionsElectrical Service Guide ThreeInput Voltage 400 Input Amperes At Rated Output Connecting Input Power Welding Power Source Input Power ConnectionsDisconnect Device Input Power Connections Selecting Weld Cable Sizes − Recommended Setup ProceduresGun TravelWCL Current Flow Path Welding CircuitBad BetterBest Using Multiple Welding Power Sources Wire Feeder Drop in the workpiece. The voltage drop Bad SetupSupporting separate voltage feedback to OM-230 032 Better SetupBest Setup Front Panel Switches − OperationOptions − Maintenance Routine MaintenanceBlowing Out Inside Of Unit Shock Hazard from testing − Safety Precautions for ServicingServicing Hazards Exploding Parts can cause injuryCalifornia Proposition 65 Warnings Removing Cover and Measuring Input Capacitor Voltage − TroubleshootingWeld Process Board PC4 Diagnostic LED’s Diagnostic LED’s On Process Board PC4Status Diagnosis Module Status LED’s Network And Module Status LED’s Network Status LED’sRed Circuit board is operating normallyTrouble Remedy TroubleshootingOM-230 032 Circuit Diagram For Welding Power Source − Electrical Diagrams229 810-A − Parts List − Fig17 − Fig 1411 HD2 Windtunnel Assembly LH And RH Windtunnel Assembly LH And RH 1Item Top Tray Assembly Rear Panel Assembly Front Panel Assembly Dia Part Page Service Your distributor also givesSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

Axcess 300 specifications

The Miller Electric Axcess 300 is a cutting-edge power source designed for advanced welding applications. This machine stands out in the marketplace for its unique combination of features, performance, and versatility. Ideal for industrial environments, the Axcess 300 is particularly well-suited for multi-process welding, allowing users to engage in MIG, TIG, and Stick welding with ease.

One of the hallmark features of the Axcess 300 is its exceptional output capability. With a maximum output of 300 amps, this machine is equipped to handle a variety of welding tasks ranging from light to heavy fabrication. The machine can easily accommodate materials of varying thicknesses, making it an exceptional choice for diverse welding projects.

Incorporating Miller's advanced Auto-Set technology, the Axcess 300 simplifies the setup process for welders. With just a few inputs from the operator, the machine intelligently adjusts itself to provide optimal welding conditions, ensuring high-quality results without the need for extensive expertise. This feature is especially beneficial for less experienced welders, allowing them to produce excellent welds with minimal guidance.

The Axcess 300 employs Miller's innovative X-Mode technology, which helps to maintain a stable arc even when working with challenging materials or in fluctuating conditions. This enhances arc control, minimizing defects such as spatter and burn-through. Moreover, the machine's extensive voltage range allows for superior performance over different welding procedures, contributing to more efficient operation overall.

Enhanced portability is another important characteristic of the Axcess 300. Its compact design and lightweight construction make it easy to transport, allowing operators to quickly move the machine to different job sites. The durable enclosure protects against the rigors of industrial use, ensuring a long operational lifespan.

Safety features integrated into the Axcess 300 include a built-in thermal overload protection system, which prevents the machine from overheating during heavy usage. Furthermore, the intuitive interface with easy-to-read displays allows for straightforward operational controls, enabling welders to focus on their work without unnecessary distraction.

In summary, the Miller Electric Axcess 300 is a versatile, powerful, and user-friendly welding power source that combines advanced technology with practical features, making it an invaluable asset for professionals in various sectors.
Top Page Image Contents