Miller Electric Axcess 300 manual Network And Module Status LED’s Network Status LED’s, Red

Page 41

9-4. Network And Module Status LED’s

A.Network Status LED’s

The following is a network status LED:

LED4 on the PCM circuit board.

Status

Diagnosis

 

 

Off

The circuit board is not on-line with the network or there is no power applied to the circuit board.

 

 

Green

The circuit board is operating normally and the on-line connection is made with the network.

 

 

Flashing Green

The circuit board is waiting for an on-line connection to be made with the network.

 

 

Red

The circuit board has encountered a communication link failure with the network. Check DeviceNet cable connections. Verify

 

dip switch positions according to Sections 1-2 and 1-3. Replace circuit board if necessary.

 

 

B.Module Status LED’s

The following is a module status LED:

LED3 on the PCM circuit board.

Status

Diagnosis

 

 

Off

There is no power applied to the circuit board or the board software is not executing its functions.

 

 

Green

The circuit board is operating normally.

 

 

Flashing Red

The circuit board has encountered a recoverable fault. Wait or cycle power to clear fault.

 

 

Red

The circuit board has encountered an unrecoverable fault.

 

 

OM-230 032 Page 35

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Processes OM-230 032CDescription File Advanced Manufacturing SystemsFrom Miller to You Table of Contents − Troubleshooting Decstat1/07 DirectivesStandards Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesserLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-230 032 − Definitions Disconnect input plug or power before working on machineManufacturer’s Warning Label Definitions Keep your head out of the fumesWeee Label I1max Symbols And DefinitionsI1eff Manufacturer’s Rating LabelDimensions And Weight − InstallationSpecifications Volt-Ampere Curves Duty Cycle And Overheating100% Duty Cycle At 225 Amperes OverheatingSelecting a Location Connection DiagramMovement Tipping Do not move or operate Location115 V 10 a AC Receptacle RC2 Rear Panel Receptacles And Supplementary ProtectorsReceptacle supplies From RC2 is limited by supplementaryConnecting To Weld Terminals Pin Network Wire Feeder Receptacle FunctionsInput Voltage 400 Input Amperes At Rated Output Electrical Service GuideThree Disconnect Device Input Power Connections Connecting Input PowerWelding Power Source Input Power Connections Selecting Weld Cable Sizes − Recommended Setup ProceduresGun TravelWCL Current Flow Path Welding CircuitBest BadBetter Using Multiple Welding Power Sources Wire Feeder Drop in the workpiece. The voltage drop Bad SetupSupporting separate voltage feedback to OM-230 032 Better SetupBest Setup Options Front Panel Switches− Operation Blowing Out Inside Of Unit − MaintenanceRoutine Maintenance Shock Hazard from testing − Safety Precautions for ServicingServicing Hazards Exploding Parts can cause injuryCalifornia Proposition 65 Warnings Removing Cover and Measuring Input Capacitor Voltage − TroubleshootingStatus Diagnosis Weld Process Board PC4 Diagnostic LED’sDiagnostic LED’s On Process Board PC4 Module Status LED’s Network And Module Status LED’s Network Status LED’sRed Circuit board is operating normallyTrouble Remedy TroubleshootingOM-230 032 Circuit Diagram For Welding Power Source − Electrical Diagrams229 810-A 17 − Fig 1411 − Parts List− Fig HD2 Windtunnel Assembly LH And RH Windtunnel Assembly LH And RH 1Item Top Tray Assembly Rear Panel Assembly Front Panel Assembly Dia Part Page Support ServiceYour distributor also gives Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

Axcess 300 specifications

The Miller Electric Axcess 300 is a cutting-edge power source designed for advanced welding applications. This machine stands out in the marketplace for its unique combination of features, performance, and versatility. Ideal for industrial environments, the Axcess 300 is particularly well-suited for multi-process welding, allowing users to engage in MIG, TIG, and Stick welding with ease.

One of the hallmark features of the Axcess 300 is its exceptional output capability. With a maximum output of 300 amps, this machine is equipped to handle a variety of welding tasks ranging from light to heavy fabrication. The machine can easily accommodate materials of varying thicknesses, making it an exceptional choice for diverse welding projects.

Incorporating Miller's advanced Auto-Set technology, the Axcess 300 simplifies the setup process for welders. With just a few inputs from the operator, the machine intelligently adjusts itself to provide optimal welding conditions, ensuring high-quality results without the need for extensive expertise. This feature is especially beneficial for less experienced welders, allowing them to produce excellent welds with minimal guidance.

The Axcess 300 employs Miller's innovative X-Mode technology, which helps to maintain a stable arc even when working with challenging materials or in fluctuating conditions. This enhances arc control, minimizing defects such as spatter and burn-through. Moreover, the machine's extensive voltage range allows for superior performance over different welding procedures, contributing to more efficient operation overall.

Enhanced portability is another important characteristic of the Axcess 300. Its compact design and lightweight construction make it easy to transport, allowing operators to quickly move the machine to different job sites. The durable enclosure protects against the rigors of industrial use, ensuring a long operational lifespan.

Safety features integrated into the Axcess 300 include a built-in thermal overload protection system, which prevents the machine from overheating during heavy usage. Furthermore, the intuitive interface with easy-to-read displays allows for straightforward operational controls, enabling welders to focus on their work without unnecessary distraction.

In summary, the Miller Electric Axcess 300 is a versatile, powerful, and user-friendly welding power source that combines advanced technology with practical features, making it an invaluable asset for professionals in various sectors.
Top Page Image Contents