Dia Part | Miller Electric Axcess 300 specs

Miller Electric Axcess 300 manual Dia Part

Page 53

Item	Dia.	Part
No.	Mkgs.	No.	Description	Quantity
			Figure 11-5. Front Panel Assembly (Continued)

. . . 14 . . . . . . . . . . . . . . . . 207979 . . . Box, Louver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . 15 . . . . . . . . . . . . . . . . 186621 . . . Boot, Generic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

. . . 16 . . . . . PL1 . . . . . . 163562 . . . Light, ind white lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . 17 . . . . . . . . . . . . . . . . 212777 . . . Nameplate, Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . 18 . . . . . . . . . . . . . . . . 210865 . . . Terminal, Pwr Output Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . 19 . . . . . . . . . . . . . . . . 210483 . . . Bracket, lift eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . 20 . . . . . . . . . . . . . . . . 210358 . . . Bolt, eye shld thd stem .500−13 X 1.500 . . . . . . . . . . . . . . . . . . . . . . . . . . 1

. . . 21 . . . . . . . . . . . . . . . . 207980 . . . Bus Bar, output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

*Recommended Spare Parts.

+When ordering a component originally displaying a precautionary label, the label should also be ordered.

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested Replacement Parts. Model and serial number required when ordering parts from your local distributor.

OM-230 032 Page 47

Image 53

Contents

Processes OM-230 032CDescription File Advanced Manufacturing SystemsFrom Miller to You Table of Contents − Troubleshooting Decstat1/07 DirectivesStandards Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burnsARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyesFire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injuryCalifornia Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical DevicesUNE Décharge Électrique peut entraîner la mort Symboles utilisésLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesserLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-230 032 − Definitions Disconnect input plug or power before working on machineManufacturer’s Warning Label Definitions Keep your head out of the fumesWeee Label I1max Symbols And DefinitionsI1eff Manufacturer’s Rating LabelDimensions And Weight − InstallationSpecifications Volt-Ampere Curves Duty Cycle And Overheating100% Duty Cycle At 225 Amperes OverheatingSelecting a Location Connection DiagramMovement Tipping Do not move or operate Location115 V 10 a AC Receptacle RC2 Rear Panel Receptacles And Supplementary ProtectorsReceptacle supplies From RC2 is limited by supplementaryConnecting To Weld Terminals Pin Network Wire Feeder Receptacle FunctionsInput Voltage 400 Input Amperes At Rated Output Electrical Service GuideThree Disconnect Device Input Power Connections Connecting Input PowerWelding Power Source Input Power Connections Selecting Weld Cable Sizes − Recommended Setup ProceduresGun TravelWCL Current Flow Path Welding CircuitBest BadBetter Using Multiple Welding Power Sources Wire Feeder Drop in the workpiece. The voltage drop Bad SetupSupporting separate voltage feedback to OM-230 032 Better SetupBest Setup Options Front Panel Switches− Operation Blowing Out Inside Of Unit − MaintenanceRoutine Maintenance Shock Hazard from testing − Safety Precautions for ServicingServicing Hazards Exploding Parts can cause injuryCalifornia Proposition 65 Warnings Removing Cover and Measuring Input Capacitor Voltage − TroubleshootingStatus Diagnosis Weld Process Board PC4 Diagnostic LED’sDiagnostic LED’s On Process Board PC4 Module Status LED’s Network And Module Status LED’s Network Status LED’sRed Circuit board is operating normallyTrouble Remedy TroubleshootingOM-230 032 Circuit Diagram For Welding Power Source − Electrical Diagrams229 810-A 17 − Fig 1411 − Parts List− Fig HD2 Windtunnel Assembly LH And RH Windtunnel Assembly LH And RH 1Item Top Tray Assembly Rear Panel Assembly Front Panel Assembly Dia Part Page Support ServiceYour distributor also gives Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

Miller Electric Axcess 300 manual Dia Part

Dia.

Part

Figure 11-5. Front Panel Assembly (Continued)

OM-230 032 Page 47