Miller Electric CP-302, CP-252TS manual Fire or Explosion hazard, Moving Parts can cause injury

Page 7

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.

MOVING PARTS can cause injury.

DKeep away from moving parts such as fans.

DKeep all doors, panels, covers, and guards closed and securely in place.

FALLING UNIT can cause injury.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling boards or parts.

DUse proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can cause injury.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can cause injury.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

OM-259 Page 3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Description ProcessesFrom Miller to You Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesFalling Unit can cause injury Welding Wire can cause injuryFire or Explosion hazard Moving Parts can cause injuryEMF Information Principal Safety StandardsAbout Pacemakers Identifie un message de sécurité particulier Signification des symbolesLES Décharges Électriques peuvent être mortelles LES Fumées ET LES GAZ peuvent être dangereuxLE Bruit peut affecter l’ouïe LE Soudage peut causer un incen- die ou une explosionLES Particules Projetées peu- vent blesser les yeux LES Pièces Chaudes peuvent cau- ser des brûlures gravesLES Pièces Mobiles peuvent cau- ser des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut FaireInformation sur les champs électromagnétiques Principales normes de sécuritéConsignes relatives aux stimulateurs cardiaques 230 380 400 SpecificationsDuty Cycle And Overheating 200Ampere Models Volt-Ampere CurvesDimensions Dimensions And WeightsWeight Selecting a Location Do not move or operate unit where it could tipMovement Tipping For GMAW, use optional gas valve Slope Connection Label Tapped Reactor AC-Z And Slope Coils Slope Selection 250 Ampere ModelInductance Selection 300 Ampere Models Remote 14 Receptacle Information Weld Output Terminals And Selecting Cable SizesARC Welding can cause Electromagnetic Interference Electrical Service Guide Connecting To 115 Volts AC Duplex Receptacle+/- 5 in lb Placing Jumper Links= GND/PE Earth Ground Connecting Input PowerMonths Routine MaintenanceDisconnect power ControlsReplacing Fuses Overload ProtectionTrouble Remedy Troubleshooting− Electrical Diagrams Circuit Diagram For 300 Ampere Models OM-259 − Parts List Complete Assembly Panel, Front w/Components RC8 Rectifier Assembly Support ServiceMiller Electric Mfg. Co Owner’s Record

CP-302, CP-252TS specifications

The Miller Electric CP-252TS and CP-302 are advanced power sources designed to meet the demands of both the industrial and manufacturing sectors. Known for their reliability and performance, these models are ideal for a variety of welding applications, including MIG, TIG, and stick welding.

One of the main features of the CP-252TS is its superior arc stability, which is essential for achieving high-quality welds. This model integrates Miller's Auto-Set technology, enabling users to easily configure their welding parameters for optimal performance. By simply selecting the material type and thickness, the machine automatically adjusts voltage and wire feed speed, streamlining the setup process and significantly reducing the likelihood of user error.

In contrast, the CP-302 model emphasizes versatility and connectivity, offering multiple welding processes in one machine. It is equipped with a robust wire feeder that can handle various wire diameters, making it suitable for both thin sheet metal and thicker materials. The CP-302 also features Miller’s advanced inverter technology, ensuring high energy efficiency and reducing power consumption. This makes it an environmentally friendly option without compromising on performance.

Both models come equipped with a user-friendly interface, allowing operators to monitor and adjust settings with ease. The clear LCD display provides critical information at a glance, improving workflow and efficiency in high-demand environments. Additionally, these machines are designed with durability in mind, featuring rugged construction that withstands the rigors of daily use in challenging industrial conditions.

Safety is a priority with the Miller Electric CP-252TS and CP-302. They include advanced protection features that prevent overheating and electrical overloading, ensuring both equipment longevity and operator safety. Furthermore, Miller's commitment to compliance with industry standards means these machines offer peace of mind in terms of regulatory adherence.

In summary, the Miller Electric CP-252TS and CP-302 are exceptional choices for professionals looking for reliable, efficient, and versatile welding solutions. Their combination of advanced technology, user-friendly design, and robust safety features make them indispensable tools in any welding operation. Whether for fabrication, maintenance, or production, these power sources deliver the performance and efficiency required to keep pace with modern industrial demands.
Top Page Image Contents