Miller Electric D-64 manual Introduction, Installation, Specifications, Site Selection

Page 15

SECTION 3 – INTRODUCTION

3-1. Specifications

	Type of Input	Welding Power	Wire Feed	Wire Diameter	Welding	IP	Overall
	Type of Input	Welding Power	Wire Feed	Wire Diameter	Circuit	IP	Overall	Weight
	Power	Source Type	Speed Range	Range	Circuit	Rating	Dimensions	Weight
	Power	Source Type	Speed Range	Range	Rating	Rating	Dimensions
					Rating

			Standard: 50 To	.023 To 1/8 in	100 Volts,		Length: 32 in
			780 ipm (1.3 To	.023 To 1/8 in	100 Volts,		Length: 32 in
	24 Volts AC	Constant Voltage (CV)	19.8 mpm)	(0.6 To 3.2 mm)	750		(812 mm)
	Single-Phase	Constant Voltage (CV)			Amperes,		Width: 18 in	78 lb
	Single-Phase	DC With 14-Pin And			Amperes,	IP 23	Width: 18 in	78 lb
	10 Amperes	DC With 14-Pin And	Optional High	Max Spool	100% Duty	IP 23	(457 mm)	(35 kg)
	10 Amperes	Contactor Control	Optional High	Max Spool	100% Duty		(457 mm)	(35 kg)
	50/60 Hertz	Contactor Control	Speed: 90 To	Weight: 60 lb	Cycle		Height: 14 in
	50/60 Hertz		Speed: 90 To	Weight: 60 lb	Cycle
			1400 ipm (2.3 To	(27 kg)
			1400 ipm (2.3 To	(27 kg)			(356 mm)
			35.6 mpm)				(356 mm)
			35.6 mpm)

SECTION 4 – INSTALLATION

4-1. Site Selection

2

4

1

7

5

6

3

1Wire Feeder

2Lifting Eye

3Rubber Feet

4Slot

Choose slot that allows all rubber feet to sit securely on top of welding power source.

5Wire Spool/Reel

6Gas Cylinder (Customer Supplied)

7Welding Power Source

YDo not put feeder where welding wire hits cylinder.

YDo not move or operate equipment when it could tip.

Ref. ST-152 468-A / ST-152 566-B

OM-1582 Page 11

Image 15

Contents OM-1582 ProcessesDescription From Miller to You Table of Contents Standards DirectivesElectric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesPrincipal Safety Standards About Pacemakers EMF InformationLES Fumé ES ET LES GAZ peuvent ê tre dangereux Signification des symbolesConsignes DE Securite Lire Avant Utilisation UN Choc É Lectrique peut tuerLE Soudage peut provoquer un incendie ou une explosion DES Particules Volantes peuvent blesser les yeuxLE Bruit peut affecter l’ouïe DES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OULA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peutPrincipales normes de sé curité Information sur les champs é lectromagné tiquesConsignes relatives aux stimulateurs cardiaques Definitions + + +Rating Label For CE Products Symbols And DefinitionsSite Selection InstallationSpecifications IntroductionGun Recommendation Table Equipment Connection DiagramsRear Panel Connections Pin Plug InformationPin Information Wire Type, Size, And Feed Speed Capability Table Motor Speed Wire Type Wire Size Feed Speed CapabilityMotor Start Control Rotating The Drive Assembly To adjust drive roll pressure, hold nozzle Installing And Threading Welding WireSpot Time Range SelectionOption Interface Standard Settings Optional Equipment DIP Switch SettingsFront Panel Controls OperationOverload Protection And Optional Side Panel Controls Maintenance and TroubleshootingRoutine Maintenance Disconnect power before maintainingTroubleshooting Disconnect power before troubleshootingTrouble Remedy OM-1582 Circuit Diagram Electrical Diagram197 518-A Main Assembly Parts ListOptional Control Box Control Box -1 Item Panel, Front w/Components Panel, Front w/Components -2 Item Control Panel Drive Assembly, Wire Drive Assembly, Wire -1 Items 15 Drive Roll And Wire Guide Kits Fraction Metric Kit Roll Wire SizeRoll Drive OM-1582 Support ServiceMiller Electric Mfg. Co Owner’s Record