Miller Electric D-64 manual Optional Equipment DIP Switch Settings

Page 21

4-10. Optional Equipment DIP Switch Settings

. If wire feeder is equipped with a voltage sensing lead, set DIP switch S3

to the OFF position (up). If wire feeder is NOT equipped with a voltage sensing lead, set DIP switch S3 to the ON position (down).

Spot Time

Range SelectionOption Interface

Standard Settings

OFF

2	1

	OFF

2

1

1 2

Long Spot

Time

0-5 Seconds

Or

Short Spot

Time

0-2.5 Seconds

OFF

2 1

X Means switch can be in either position.

. Means switch must be in this position.

							Digital Meter Functions
	Standard									Standard						High Speed										High Speed
	Standard									Standard						High Speed										High Speed
			Motor								Motor							Motor									Motor
Inches/Minute									Meters/Minute							Inches/Minute									Meters/Minute

							5					5											5								5
							5					5											5								5


							4							4									4								4
							4							4									4								4
																								Or

							3	Or						3									3								3
							3	Or						3									3								3


							2					2											2								2
							2					2											2								2


							1							1									1								1
							1							1									1								1

	Voltage Sensing Function
Arc Voltage Sensing Using								Arc Voltage Sensing Using
Arc Voltage Sensing Using								Feedback From Welding
Voltage Sensing Lead									Power Source

						2	Or							2
						2								2

						1								1
						1								1


	DIP Switch S3								DIP Switch S3
		Set To OFF								Set To ON

Tools Needed:

1/4 in

Ref. 143 259-G / Ref. SA-146 866-B / Ref. SA-148 666-E / Ref. SA-150 588-D

OM-1582 Page 17

Image 21

Contents OM-1582 ProcessesDescription From Miller to You Table of Contents Standards DirectivesMarks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killPrincipal Safety Standards About Pacemakers EMF InformationConsignes DE Securite Lire Avant Utilisation Signification des symbolesUN Choc É Lectrique peut tuer LES Fumé ES ET LES GAZ peuvent ê tre dangereuxLE Soudage peut provoquer un incendie ou une explosion DES Particules Volantes peuvent blesser les yeuxLE Bruit peut affecter l’ouïe LA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU’EMPLOI Excessif peut DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sé curité Information sur les champs é lectromagné tiquesConsignes relatives aux stimulateurs cardiaques Definitions + + +Rating Label For CE Products Symbols And DefinitionsSpecifications InstallationIntroduction Site SelectionGun Recommendation Table Equipment Connection DiagramsRear Panel Connections Pin Plug InformationPin Information Wire Type, Size, And Feed Speed Capability Table Motor Speed Wire Type Wire Size Feed Speed CapabilityMotor Start Control Rotating The Drive Assembly To adjust drive roll pressure, hold nozzle Installing And Threading Welding WireSpot Time Range SelectionOption Interface Standard Settings Optional Equipment DIP Switch SettingsFront Panel Controls OperationRoutine Maintenance Maintenance and TroubleshootingDisconnect power before maintaining Overload Protection And Optional Side Panel ControlsTroubleshooting Disconnect power before troubleshootingTrouble Remedy OM-1582 Circuit Diagram Electrical Diagram197 518-A Main Assembly Parts ListOptional Control Box Control Box -1 Item Panel, Front w/Components Panel, Front w/Components -2 Item Control Panel Drive Assembly, Wire Drive Assembly, Wire -1 Items 15 Drive Roll And Wire Guide Kits Fraction Metric Kit Roll Wire SizeRoll Drive OM-1582 Support ServiceMiller Electric Mfg. Co Owner’s Record